French Car Forum

My wife's car has had lumpy starting and running, until it gets warmed up, for a while now. It is a 2008, 1.6 petrol VTI
There is a PO114 fault code that reoccurs (it is the only fault code) and the depollution.. warning. I've change the camshaft sensors and swapped them over and it is always Bank 2. Also the associated oil valves. Cleaned and...

Hi
I'm in need of a 2.8 Turbo Diesel for my Boxer Van

2009 207cc 1.6thp
Any hints on this one greatly appreciated, as this is currently kicking my arse!!
Little bit of history:
Car had a death rattle on startup, if left to warm up rattle went away. I suspected the hydraulic tensioner on it's way out. But seemed fine once warm, so she drove it locally while I got round to doing it. Next it wouldn't...

Hi,
I was changing the rears on the peugeot for the missus who took the brakes down to an impressive 0 percent and disk lets not mention the disks.

Fronts went fine. No problems as expected.
However on putting car into maintenance mode and retracting brakes for disk and caliper removal a fault occurred I think it lies in the right hand caliper...

Greetings All!

New member here, and my first foray into the realm of les anciennes voitures francaises with the recent purchase and impending delivery of a quite adorable 1998 Peugeot 306 Cabrio, Right-hand drive, of course, Because....well, just because. This one was imported to the States under the 25 Year Rule so, I guess that it came from...

Hi all,

I am hoping somebody in the know could help me with which part numbers relate to what on the ecu.

Most specifically, I am wondering if the number circled in red is unique to this ecu and will be different on every ecu with the same 'main' part number? Or will it match another ecu out there?

By 'main' part number I mean the 980.. number...

Hello all, help needed!
After much head scratching and internet perusing I am hoping that the knowledgeable folk on this forum may be able to assist.P11A9
I recently replaced the engine on my 308 (8FR engine) due to the original having a cracked block.
At the same time I renewed the timing chain (using all timing tools), changed the oil (5w 30)...

Hello everyone !

I havre a 2004 Peugeot 407SW with a 2.2 petrol and 6 speed manual transmission.

The problem I have is a intermittent, although it is now a permanent long cranking start issue. I get a cam sensor code P0341 when I have the no start issue.
testing the input to the sensor I discovered something very strange, I have my 5 volt...

Hi all, I have a Peugeot 508 BlueHDI 150 GT line, 2015.

I'm in the process of swapping out my clutch and flywheel assembly. I have a brand new clutch from the dealer along with the slave cylinder and a crank seal. I did however get a Valeo flywheel from an online auction site which is old stock and, whilst having a little corrosion looks to be...

I noticed a puddle of oil on my under tray when I topped up my washer fluid. I’m not sure where the leak is coming from, but I’ve attached some pictures and a video to help identify it. Any advice would be appreciated!

Hi everyone,

I'm having an issue with the rear window defogger/defroster on my car—it’s not working properly. When I turn it on, the side mirrors heat up as expected, but the rear defroster doesn’t seem to work.

I checked the voltage at the connectors in the back, and I noticed that it increases very slowly, by about 0.1V every 5 seconds....

Hi,

I want to buy steel wheels for winter tires 205/55/R16 for my car but I have doubt about dimensions. I found on the internet that it should be 4x108cm, 7J ET32 but a local seller told me that I can use wheels for the C4 also which is 6.5J ET27. Is it true? He told me that the dimensions for aluminum and steel are not the same, that for steel...

Peugeot 407 coupe JUHZJ 2006.
Looking at
Model 407 Body: COUPE 2 DOORS / Engine: 2.7 HDi particle emission filter mechanical emission control REGULATOR BOX EXH TEMP PROBE

The error P0546 “Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 1.”
Is in fact not very clear which temp sensor is concerned and there are FOUR in total around...

Good day, I have a Peugeot 207 fitted with an automatic heating system. The Climate control heating/AC fan stopped working inside the car checked all the wiring I checked fuse F13 on PSF1 and R7 all ok going to 8045 pins 1 and pin 2 to MC37 fan speed control unit, checking pin 5/6 on the 8045 unit I am missing a PWM signal from unit 8080 AC ECU,...

Hi everyone
The central locking on my Australian delivered 2001 Peugeot 306 Cabriolet will lock then unlock a short time after. It can take many attempts to get it to stay locked.
Anyone here had this problem and been able to fix it?
If so, what was the problem and how was it fixed.
Remote locking from the key no longer works as well.
The battery...

Hi all.
I own the above car. It's done 42262 miles and the dash is saying that maintenance is due.
Could anyone share the servicing and maintenance schedule for this particular model?
I plan on keeping the car so does anyone know of any issues or things to watch out for?
Cheers

Hi,

It has been sometime that my 2007 407SW 2.2 Petrol has been making a diesel noise / rattle. This is especially apparent during cold start or high RPM. To my understanding, the sound is caused by a failing VVT Cam Gear. I am wondering, how bad should things get before I spend the money to replace it? Since it is a quite an expensive part. I...

Hi. I bought a used Peugeot 207 2011, 1.4, kft. I'm crazy about him. All tests point to the control unit. Before we order it, could you please provide a wiring diagram of the control unit? let's check everything properly one more time. thank you very much Anna

Hi all,

Didnt know where to open this, hope its in the right place! Looking for info on my gearbox and oil capacity

Would it be possible to check the gearbox code in my 2015 Boxer based on the VIN VF3**************[VIN obfuscated, can be read by forum staff]

I believe its a 20gp17, but am I correct in saying there are 2 variants? One requiring 2.4 litres, the other 2.8?

Thanks!

Hello,i have peugeot 407 coupe,2010 year, 2.0 diesel,manuel.i help some guy start car with crocodile from my car and after that get eror code U1113,U0122 i can delete them,but when start car they are back,simptones,abs/esp spidometer isnt working,the lights liwe her life,going up sometimes down,,uneven growling,and other things,

Having partially fixed my DPF regeneration issue (so far all okay but still blowing a cloud of dark smoke on take off), Diag global test comes up with a permanent fault P1351 pre/post relay heating circuit / glow plugs.

I found the relay 0281003018 under the ECU but can't seem to spot the glow plugs themselves on the engine ?

Any diagrams /...

Does anyone have the diagram of the wiring for installing a aftermarket analogue alarm system in a Peugeot 307 break (2004)?
I need to know where to connect the cables from the alarm to.

I have a automatic AC in my 307 break. Is the ventilation control suppose to work when the AC is turned off?

Hi all, my 3008 1.6 hdi (9HR) died on me a couple of weeks ago coming home from shopping, at first, warning Battery Charge Fault came up as I parked in store car park. Checked alternator belt 'ok', Started her back up and no fault. As I pulled out of car park onto duel carriage way dash lights lit up and engine died, engine started back up before...

In short, lost the last original key. I have a new key without a transponder chip using the key code. The company came by to program a new key with a new chip (reading the computer (ECU)), but it didn't work. Couldn't get into the computer. Then bought a similar ECU with the corresponding transponder chip. The engine started 3 times, that was it....

Hi,

I spotted an unconnected negative wire and an electrical connector of some kind hooked up to the battery of my boxer van (2022).

Anyone know what they are for?

Many thanks
Peter

IMG_20241010_150245.jpg
IMG_20241010_150314.jpg

So i’m having a mare trying to proxy align my instrument cluster, diagbox wont do it, tried alfaobd getting failed any ideas?
IMG_4614.jpeg
Boxer 2.2D euro 5 2013 vin number VF3**************[VIN obfuscated, can be read by forum staff]

Thanks

So I have diagbox and have multiple airbag ecu’s listed. Have tried a guy to do remote coding via the psa network and he also gets instrument cluster and airbag ecu failed to align and advised to try the foat version to see if the cluster will realign I cannot get it coded offline or online via diagbox v7.57 &9.58 anybody got any ideas?
Turns out...

So here's my problem any help would be greatly appreciated. Have a XUD9A block uses a crack shaft casting 182 or 620 part number oem is 0501H1. Here in the USA these parts are hard to come by. So I was sent a crankshaft casting number 136 oem part number 0501N8. The oem crankshaft had a 8 web crankshaft design while replacement has a 4 web design....

I have gotten a 2006 Peugeot Partner 2.0 hdi but the VIN won't generate any results in Service Box or SSG Asia.

I need to find the correct part catalogue and repair instructions for this but have a hard time knowing exact engine model and gearbox.

Can anyone help me decode this vin? I would appreciate all or any help

VF3**************[VIN obfuscated, can be read by forum staff]

Hi Folks

I had the Timing belt and water pump changed recently. Since then the car is running in limp mode. A basic OBDII scan shows - P0341 camshaft position (CMP) Sensor A, bank 1- range performance error and a P2562 Turbo charger low boost error. I've not got round to using Diagbox just yet as I need to find my interface.
I've spoken to the...

Hi Does anybody know what the code card number will be to get into the marelli BCM? To do a proxy alignment i’ve getting asked for code card any ideas where i would find this I don't have any books or anything

Hello,

I have a couple of codes that are a bit of a head scrather, don't know what to do with them.

This is on my Peugeot 5008 MKII 1.6BlueHDI 120BHP. VIN VF3**************[VIN obfuscated, can be read by forum staff]

Built-in systems interface BSI2010_EV
B1865 23 Lack of coherence between the status of the engine starting switch and the status of the built-in systems interface internal...

Hi all.

Can anyone help me to get the official maintenance plan and schedule (the what and when do). I tried to get it from the dealer... no luck. I have the Haynes manual... well, poor, very poor.

Thank you in advance

Hi, I have the issue in my 2016 508 1.6 Diesel where intermittently, I get ABS, ESP, Anti Rollback and parking brake alarms coming on. When I switch off the car for a little while, the faults are gone. I had some other intermittent faults with doors and Electrical Fault service car or something similar. I bought the car last October and this...

Hi

My 2013 diesel Peugeot is in limp mode with a faults P1434 and P1435 on the fuel additive pump. It’s done 130,000 miles.

My regular garage changed the pump but it didn’t resolve the fault. He says he’s not the guy to take it further; and can’t recommend anyone.

I’ve taken it in for an initial investigation at the main dealer. They say no...

Anyone know if the scuttle panel on a 307 was sealed to the windscreen when they were new? Just had my windscreen replaced and fitter assured me that it was not supposed to be sealed.

I am hoping to get some advice on a 206 that has a aftermarket drivers seat fitted. I want to fit a resistor to bypass the airbag warning light on the dash.

There are 2 connector plugs from the loom. One is a green 3 pin and the other is a White 2 pin which I assume is for the airbag. Do I need to fit 2 resistors one for each plug? and do I need...

Hi
I am seeking to clean a few things in my engine, namely: the glow plugs, the inlet manifold, and fuel injectors.
To do this, it appears I need to remove a very solid metal bar/cylinder over the engine that I believe is some airflow (after the turbo?) cylinder.
Can someone help answer: can I remove this and then how? I have unscrewed the hose...

I have an elderly 2008 which, some years ago began to rattle/rumble from what I took to be the rear but which now seems to have settled in front offside position. Being ancient I dont do mny miles but it seems to be getting worse, I have taken it to three garages none of whom could identify it or its source though or they charged steeply for this...

Hi, first time poster in need of some advise pease , I’m self employed and own a Peugeot Partner 1.6 hdi 67 55000 miles
This is my 5th French van over the years, but the first I’ve owned out right, six years trouble free, serviced every year.
12 months ago the van developed a fault and a new catalytic converter and nox sensor fitted. My van has...

I'm unsure if I should put this in the 308 forum, but it does seem to be the same problem as described here.

On a 2015 308 I had disconnected the battery to try and locate an intermittent fault on the air bag. After re-connecting the battery and then locking the car using the remote key, the alarm sounds straight away. So I think that it needs...

Hi,
Firstly I apologise if there's already a thread on this, if there is I couldn't find it. Car is a 2002 307 Rapier 2.0 Hdi with 5 speed gearbox which I think is an MA5. There was no horrid noises, just parked it up one night and when I drove it next morning no third gear, all other gears work fine so not the clutch. I've taken out the trim...

Hi

I'm making some external repairs to my 508, and one detail that bothers me is the presence of some cracks in the plastic frames around the sunroof (external part at the roof), they are frontal and lateral plastic frames in piano black.

I still haven't figured out if it's possible to remove just these frames, or if it's part of the entire...

Hi everyone,

Was recently given a 307 2.0 petrol with the Tiptronic transmission. Realised after a couple of days that I don't remember when last I saw one on the road (any variation 3/5 door or Estate).

I actually purchased this vehicle new at the end of 2003, then gave it to my folks in 2006. That makes it 21 years old, give or take. It...

Hi All, I am thinking of buying a 508 for the wife a 2013 one.. What are the main failure points on them to look for. Is the 1.6 more or less reliable or is it much of a muchness.

So I've got the diesel additive warning message on my 2010 peugeot 308 2.0 HDi 163 hp.

I found ample information on how exactly to top up the PAT fluid tank but I stumbled upon quite a few difficulties exploring the diagbox software. I still haven't done anything, I am trying to find out four things:
1. How much fluid do I need
2. What fluid do I...

Hurray peoples,

today i was able to solve the low oil pressure message on my car.

Since i've read many and many articles and watched videos about this subject without finding a solution, let me tell you what happened in my case.

Off course when the problem first started, i've looked on internet as many does, and found every possible solution....

A good few years back I caught turbo failure very early on, (took engine out, cleaned up top end) replaced turbo and, as recommended, changed the turbo oil feed pipe, banjo bolts and copper washers.

At the time of the rebuild I had issues getting the block end of the feed pipe's banjo bolt connection to be oil tight. Ultimately cured by annealing...

Hi,

Here goes -

Having a few problems with Mk1 Peugeot 3008 2015 (65)

Car was pulling to the left a couple of months just before seeting off on holiday, there was also vibration there indicating a wheel was out of balance, although there has always been a slight vibration in the couple of years weve had it.

Got wheel alingment done at a...