French Car Forum

I bought this car here in the motherland, France (my first Peugeot) about a month ago and have finally sorted the maintenance receipts (I'm the 4th owner, it would seem) and I have a few questions about service intervals and oils. The car has 193k km on it.

1) Peugeot recommends a ridiculous 120K km/10 year interval for a timing belt change. This...

Just carried out a monthly scan of my 2017 3008 1.6 HDI with 90k miles and it had B1811:96 for a fault in diesel fuel additive pump showing as intermittent, which I haven't seen before.

I did have the orange spanner symbol illuminate a few weeks ago but it had disappeared by the next start and it wasn't accompanied by a message relating to low...

Can any one help me. I have looked around the Internet but can't seem to find want I am looking for. I have a Peugeot Partner B9 and looking for a replacement catch for the rear seat, the one that locks into the floor holding the seat down. I can't seem to find a replacement or a part number can anybody help.

Morning all,

Struggling to find much regarding the specific problem I am having, and as I'm now running out of things to check, I thought it was time to ask here.

My 1.9 XUD n/a engine in my N reg 306 has refused to start via the key for some time now. I left it stored for a while over winter after discovering this due to a lack of time more...

Hi All.

I have had my 2017 308 GT Line 2.0 blue HDI in at my local Peugeot dealer.

I had pluming white steam consistent with an AdBlue injector fault.

Peugeot put it on the computer and diagnosed a failed AdBlue injector and this was replaced. This in turn had shown up a blocked DPF. I have previously had no issues with the DPF (67,000 miles),...

Hello, I own a Peugeot 308 GTI from 2018 with the 1.6l 193 kw. Yesterday the engine light and the service light came on the car also lost power. This afternoon I went to my local mechanic and the fault code P0235 popped up. This has something to do with the turbo pressure sensor. Did anyone had the same issue or can you help me to locate the...

My wife's 207 is running lovely with the exception of a very random burning smell that is really strong and comes and goes.

It smells like a burning clutch but the clutch is not slipping at all and was changed about 40k miles ago with an LUK one. The burning smell seems to have started since my wife drove through some deep flood water at the end...

Guys

Got a car from Copart, its a P5 Peugeot 308 2022 ex police. However i have couple of questions;

1 - do i need to program a replacement ballast? Spoke to stellenios & you , they reccomend a new ballast to be programmed. But its a sales guy.. i have the headlight

2 - I have some cables and a connector. Can someone please help me to figure...

Hi,

After replacing the original but faulty advance solenoid (coded) with a non coded LUCAS solenoid, I can't start the car.
The new solenoid receives +12V correctly after I start the car with the key.

A diagnostic with PP2000, shows this Default :

ECU Engine / Permanent Fault. Pump Module locked.

Tried to remove F2 fuse : issue is still...

Hi everyone, I am new to the forum and I have a few issues that I would be so grateful for any help with!

After spending hours searching forums and watching videos I am not getting anywhere!

The car is a 2012 207 1.4 vti. It starts and runs although lumpy on idle.

The fault codes I have are:

P1062 variable valve lift system position regulation...

After some advice if possible.

Trying to recalibrate the steering angle sensor on a Peugeot 5008 2012. I'm getting the following codes. I have made sure the wheels are dead ahead. But it keeps failing and illuminating the ESP light. Does it sound like the Angle sensor/ Clock spring I purchased is faulty or could it just need reinstalling? Thanks...

I spent a few hours today trying to help a friend out.

He’s got an incredibly rare 306 Cabriolet. It’s a genuine Dimma. 1 of only 2 ever made. It’s the one that featured in the Max Power magazines back in the day. It was originally yellow but when he got it the paint was trashed so he repainted it. It’s stunning and ever since he’s been here...

Matt ive lost the diagrames for the headlamp wire colours to what light for my 308cc can you pop them up here please im needed to know which wire feed what lamp on the front.

Hi everyone,

I am trying to find out if I can fit a secondhand ECU to my 2012 207 1.4 vti without the need for matching it to the car in some way.

Could anyone tell me if it will just plug in and work or is there more to it than that?

Many thanks

Hi all,
3008 GT 2019 does anyone know how to remove front plastic headrest guides/ mounts?
Thanks in advance

Since I had some issues with my 2012 Peugeot 308 RNEG unit, I've taken it out and sent it for repair. After taking the unit out, and driving without it for a couple of minutes, a check engine light appeared.
I've not noticed any changes in driving, and everything seems to be working fine (engine-related).

I wondered if the check engine light is...

Hello

I have recently just replaced the Engine Bay Fusebox 9667199780 on 207 sw due to water ingress on middle brown connector

When using tool now I have the below faults

P2426 - Exhaust Gas Recirc Valve (EGR)
P0031 - Oxygen Sensor Heater (Bank 1 Sensor 1)

When replacing fusebox I had to splice the cables to allow connection in doing this I am...

Hi everyone, I’ve just joined the forum and this is my first post hoping someone can help me to find out why my Peugeot Partner 1.6 HDI van (2012 reg, 99k miles) doesn’t start. I’ve only had this van for 5 months and last week while I was driving to local supermarket it stalled and wouldn’t start. Every time you turn the ignition you can hear and...

Hello,
WhatsApp Image 2024-03-05 at 18.28.57.jpeg
Can someone please point to i should check. i have replace the turbo actuator position sensor since fault is permeant with missing or disconnected sensor.
I have checked the voltages on the terminal socket. and measured 5 volts on point 1&2 against -ve terminal of the battery. I believe it...

Good morning

This code and the text in the attached pic popped up this morning, car seems to drive normally.

What should be the protocol for this code?

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]
IMG_20240218_095131.jpg
Thanks

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]**************

Hello,

I had a P11A3 fault code (i put up a post a few days ago) and it disappeared after replacing the VVT solenoid (stupid engineers, took me hours...) but this P0010 code popped up (and check engine light is on - i can't earse the fault, it is defined as permanent ).

The car seems to run fine , maybe...

I have a Peugeot 207 sportive 2011.
The right hand window control needs replacing. Some sites say part 6490EJ. Others say 6490EH.
Just wondering if they will both work or if there is one to choose

Hi everyone, I'm new here

I have a 2010 peugeot partner with an oil leak, I have located it to be coming from the manifold seal between 2 injectors.
I've got most of it stripped down however the HP fuel lines are in the way....has anybody got an eay way of getting these off?
Also how does the airbox come out from behind the engine?

Thanks for...

Bonjouir from downunder.
Would anyone have the circuit diagram for the control of this flap. It is the slide button type control mounted above the radio. I have the controlling motor removed and it seems to have no faults. The internal gears are ok and on full heat the ac pump turns off ok. I think the problem may be in the dash control unit. I...

hi guys the vacuum pump on my 205 1,8 d has two pipes coming out one obviouslt goes to the breaks and they work fine but the other pipe just sits in the engine bay and is cut off. can someone tell me where this goes to. Thanks

Hi all. I have a 2011 Peugeot 3008 and I am currently having problems with the (front left) ABS system. I have replaced the wheel sensor and also the wheel bearing and the ring sensor, but the ABS and ESP lights are still on. The wheel sensor has been checked and is fine, it seems as though the problem is above the sensor. Could anybody please...

Can anyone tell me if the key on my 2006 307 uses ASK or FSK modulation? Was about to buy one from Aliexpress but my existing key is obviously a universal replacement and does not have either of the original CE0536 / CE0523 markings on it anywhere.

As mentioned elsewhere, I have had issues with our 308CC not charging the battery properly. The alternator does produce current to balance the load, but the output voltage would not rise over 12.8V. usually hovering around 12.5V.

I have tried fitting a second hand alternator from a Mini Cooper with a similar Prince engine, and it is a little...

Hi guys,

I have this problem for a while, that i tried fixing but with no luck, so i came here to ask for your help. :)
Car is Peugeot 508 2011, 2.0 163HP limousine.
Problem that i am encountering is that xenon lights stays in lowest position. When i start the car i get the message (Automatic headlamp height adjustment fault) followed with...

As it just annoyed me.

When it comes to replacing the battery, is there any reason why I can't now use a wet battery of the same size and capacity, instead of the old AGM that is fitted?

Is there any difference in the charging circuit for AGM, that would preclude replacing it with wet?

Cheers

Hi Guys,

2014 Partner Horizon 1.6 Diesel Manual - Wheelchair adapted (for my daughter to use).

New to the forum, I've a good sense of humour and can take a joke and ribbing, I can give as good as I get and I'm not easily offended.

Needing a bit of advice and feedback for a fault code on the ABS ESP system, drove the car on Friday past with...

Afternoon all,

Well she went and did it so I need to expand my knowledge on the new technologies it has.

First off is the electronic parking brake. I've read that these can be a problem so how do they actually work please?

I assume that there is some kind of servo motor which winds the caliper on?

Honestly, I have no idea as I've not even...

Hi, the aircon in my 2004 206 GTi 180 has an intermittent fault. When it first occurred, the fan failed to run, but after a few days it came good. This behaviour kept repeating, but with increasingly longer periods when it wouldn't run, until it eventually it stopped working altogether. I took it to an auto electrician who tested it and said the...

Hi got peugeot boxer 2.0 hdi 2018 model driving along and just cuts out will start and drive again no probs till it cuts out again no warning changed camshaft senor and fuel rail pressure sensor any help would be great

Good evening everyone

I have issue with my hybrid system, the clutch on electric engine is not engaging so I have replaced the whole engine and diff with another working one but it’s still throwing this code P1ABF. I don’t know where else can I look so if someone can help me I would very appreciate that. Thanks...

Hello,

I’ve recently sent my van in for front brakes and discs, cambelt and water pump change and leaky thermostat and then they told me the seals needed to be done on the injectors.( all in £1300) So I got the work done and got the van back (had to set the clock) I then found an oil leak which never existed before!

I asked them to have a look...

Driving back through France to the UK last week the dashboard, and then the centre display, showed these warnings:

IMG_20200902_131145855a.jpg
This showed first and then, when the UREA warning light started flashing, these also came up:

IMG_20200902_162052584a.jpg

IMG_20200902_162103453a.jpg

At one point this message showed. I had...

I have a 2010 60 plate Peugeot 3008 2.0 163 automatic. Fully serviced and looked after.

Yesterday I accelerated hard and the revs went up but as I did so, I heard a loud pop and the car went into limp mode with errors lighting up about the gearbox ,engine, esp, parking brake.

Got home to find a rear blowout and the tyre was completely flat. That...

Hi all, 

I thought I would post this up just in case it helps anyone else in the future with the same issue.  

I have a Vivaro 2021 k0, which is an Expert.  I had an engine fault code pop up and the van went into limp mode.  Scanning gave the following faults:

- P119F Deterioration of the engine oil.  Rate of dilution excessive
- B162C...

Hi, I have topped up my additive tank 30/40k kms ago and reset it on diagbox. Now diagbox tells me there is 95 procent in it but get a pressure fault because it’s empty! How is this possible are the settings not good or is there a internal leak somewhere? There are 2 bolts on top of the tank does anyone know how to remove this?

Do I need to...

Hello
I managed to get the engine out of the van....this engine had less that 30k on it...1.9td. Its in a Ducato motorhome, I can now see the full extent of the damage.
The hole next to the starter motor is where the oil filter housing used to be.
It was lent to someone to help them out and this is how it came back!...there is a hole in each side...

Hello
Does anyone have the torque settings for the main bearing bolts and the big end bolts for the 1.9TD (XUD9)
I have two haynes manuals (405 and Xantia) but the settings are for 1.6...1.8...and 2.0l engines...there doesn't seem to be a mention of 1.9td settings.
Any help appreciated
Thanks.

Hi,

Year 2011, Peugeot 3008 1.6 HDI
VIN VF3**************[VIN obfuscated, can be read by forum staff]

After EGR replacement shows error os disconnection P0405 incorrect position open circuit or short circuit to earth. Had suspicion to it before now look during replacement just got disconnected or it loose cable.

Anybody can point me where to search second end. Loom part number or...

Hi Guys
Am considering the above new vehicle and would love to hear from those who drive one.
Are you happy with the vehicle? Has it been reliable? Would you buy another?

Thanks!

Has the title said,even after the bump a few weeks back the old girl drived ok,
Until today, drove 200miles today to start a new job tomorrow(contractor)
So after finding the site & decent parking decided to get some lunch,that's went the s... hit the fan,pulled over in a layby
A slight bang,little be of smoke or water vapour
Phone a lad who...

Hi!
My name is Daniel and Im writing from Portugal. After reading lots of topics here, I decided to write explaining my problems and making lots of questions hoping someone can help me.

Resume of problems & questions:

1 - The van had two episodes of serious trouble in injection (one injector stucked on open position I think) , making a very loud...

Hi everyone
I’m new to here , but I’m hoping someone can help me who has knowledge or advice. Ok here goes, I’ve just purchased a Peugeot Boxer 1.9td 2001 camper with the XUD 9UTF engine. I’ve just changed the timing belt and finding it difficult to find torque settings. I’ve done as per a manual I’ve purchased the bottom crankshaft bolt to...

Our 2019 308sw 1.5 hdi has started to countdown for its service very early, what can cause this ? The normal service interval should be 12 months or 20000 miles if sooner. It has always been serviced by the Peugeot dealer (Pentagon Lincoln).

It was dealer serviced on 8113 miles on 16/5/2023. Then on about 10002 miles on 21/10/2023 it started to...

Hi - I'm stressed but that is not the word !!!!

I have a 17 plate boxer, its had new water pump and timing belt, thermostat housing as it was losing water and causing a long list of associated problems - they have been solved - head gasket - dpf etc

however now my heat gauge is showing ping over to v hot and the red warning circle light...

Hi everyone! I'm having a very vexing problem with DiagBox 9.150, in short:

I own a Peugeot 208 II

I created an account on the official Peugeot/Citroen website and purchased a token.

For some strange reason I couldn't download DiagBox as there was no link to do so, so I found one online.

I connect to the car using the PC and the OBD cable, the...