French Car Forum

I'm looking into getting one myself, but there are so many versions, what do you choose? Some are listed as full chip, others lite. I take it there's a bunch of fake ones too. What do you pay attention to?

And secondly, is there any tutorial on how to set it all up on a laptop once you actually get it? I take it installing Diagbox is all it needs?

Hi,

I have been trying to install the lexia3 software but keep getting getting error

C\applic\lexia\calculo\four_004\syst_000\api_001\vers_227\\61997080.ulp

Error CRC

Does anyone know what this error means?

Or how I can move past the issue,

Thankyou in advance
Michael

The engine management light recently came on, on my 2007 C8 with the 2.0 HDI 136 engine. It went into limp mode, switched on and off and then it performed as normal again. I borrowed a CAN OBD2 code reader which gave P1351, P2408, P0489. I reset it to see which warnings came back. It came back a day later and I reset it again. A week or so later...

Hello, Im new to the forum so please forgive if I break any etiquette

I have a Grand C4 Picasso, Petrol 1.2l PureTech Auto, 2017. Which, as I understand it, is a reasonable rare combination of engine/gearbox/car. However I hope that as the forum covers Peugeot cars to which also have PureTech engines this will help input.
Recently the engine...

Hi Everyone,

I recently got the following error on my ds4 2011 2.0 hdi:
P0125 - insufficient coolant temperature for closed loop fuel control,
I replaced the thermostat with the housing and the temperature sensor and still get this error.

Does anyone know what it can be?

Thank you!

Hi. I have been a follower of this forum for a while now and I have taken the plunge and joined up. My car, a Peugeot 3008 Hybrid4 2013, has had a problem with the service (12v) battery running down. It started 3 months ago and the faults that occurred were Air bag/pretensioner dash light came on followed by the amber engine repair required dash...

Citroen C4 Picasso 2007 Diesel Semi Auto Gearbox 1.6

2 Years and 4000 miles ago Citroën Wimbledon changed Clutch kit, DM Flywheel and slave cylinder.

Please help! I have a Citroen C4 Picasso 2007 Diesel Semi Auto with Gearbox related issues. The Clutch kit was replaced 4000 miles ago. A few weeks back Gearbox Faulty message kept on coming on the...

I had previously replied to a thread that described the temperature gauge reading rapidly dropping on a C5. My DS5 did the same thing sometime after a thermostat replacement. Turns out coolant was leaking from the bleeder screw, that I had stupidly over-tightened. I eventually fixed this by using the old screw but transferring the new O-ring to...

Hi all, I have a 2011 C3 picasso and i ran out of dpf additive , which to be honest I didn't know a dpd was fitted to the car, and now I have the service light on telling me the p filter add level low. I have topped up the additive but still the pight stays on. Any ideas how to get the light reset or is it a trip to the dealer.

Hi all, I posted on this forum last year about my car ,lumpy running,well this has been an ongoing thing,been all round the houses with different fault codes showing,have been working my way through the codes short story long,the latest code,(in a long list} is p0170,what is happening is on live fuel trim data in open loop,start sits at 0.8%then...

Hi all,

Firstly sorry for a new post, I've had a look through the diagnostic section and used the search but not able to reach a conclusion myself - if there's a good particular discussion to point me at instead then please do!

I'm looking to create myself Diagbox capability.

Will buy a laptop to dedicate to the job. I've seen old Panasonic...

Hi. I have a 2004 Peugeot 206 1.4 with an automatic gearbox fault. I would like to scan the car using the Peugeot tool. My question is should I install Diagbox or Planet Peugeot? And what Windows operating system should I use? Thanks for any information \:D/

I have been running V7.62 ever since I got the kit but thought I'd update as Gibbo has been kind enough to send me his disks. I have worked through from 7.62 -7.66 - 7.74 -7.76 but when I double click the 7.76 to 7.83 update it asks me for a password!! I have checked with Gibbo but he has no knowledge of it so I was wondering if it is some form of...

Hi guys my Renault traffic 2016 diesel keeps turning off as soon as I start it.
When it first started I notice smoking coming from steering wheel gap.
Call road assistance and they said ignition switch. Mechanic checked but said something needed re soldering worked for 1 day then started Doing it again.
Key was then changed then worked for 2 days...

How do I tell my Peugeot 3008hdi that a new dpf has been fitted. I have diagbox v7. 57.i have cleared all the faults but it keeps coming up dpf worn. If I look in the parameter it says that a new one was fitted 88,000kms and has o kms left and is the only thing left that I can see to reset. Thanks

Does anyone know anything about these?

Peter

help

ive got a xsara picasso 07 1.6 16v and its got some serious problens

runs from cold for aprox 30 mins then kangaroos and then acts like its out of fuel. switch off re start and works for 20/30 mins

its had map lambda temp injectors

error p2191 error

just fitted a new fuel pump relay and the car went nuts...

i had keys in my pocket...

Hello,
I have the Actia PAS XS Evolution diag box...it is the 9780.Z5 version....(Genuine...made in France?)
The disc that came with it is no longer downloading on my laptop...(Windows 10)
I was thinking about buying a new (later version) disc..... this version has no issues with windows 10.
Before I bought it I wondered if anyone knows if this is...

Hello everybody. I need help if possible. I want to buy an OBD reader system for my citroen C5 tourer 1.6 110cv 2009 but I don't know which system is the best. I've read a lot of information, software versions, lexia, diagbox...etc. There are different prices on the internet. Aliexpress, ebay.... there are so many that I don't know which one will...

I've just bought an early 2013 Pug Partner and want to activate the Cruise Control. I have an older version of Lexia that works fine on my M59 Berlingo, but am guessing that PP2000 will not work so I'll have to use Diagbox.
I've tried Diagbox 5.29 but get a lot of 'ECU Not Recognised' messages when doing an error scan so am guessing that 5.29 is...

Hi.How i can know is my egr valve good or bad?Here are shots from diagbox.
Car is going

Car idling

Hi,
I have a Citroen Xsara Picasso 2004 - Heater Blower Resistor wiring loom.
My heater stop blowing completely, so check I had power to the blowing motor and also the motor worked when power was applied, all good.
However when I checked the Heater Blower Resistor the connection was burnt where it connects to the connector on the wiring loom.
Not...

hi there.
i have Xantia x2 with xu10jr-rfv engine and Bosch mp5.2 ECU. there is no CPH.
i bought DigBox lexia3/pp2000 and installed on win7 32bit. updated to 7.57v
the lexia 3 can show ABS and AirBag faults and test them
but cant connect to ECU for engine diagnose test. this is the erorr (picture1):
the problem is from ECU or DiagBox ?

Can someone please help me? I have this very strange problem with my Peugeot 307 CC 2004.
The problem is that the sensor in my door handle only works sometimes and sometimes only after I have disconnected it for a while and then it works for just a couple of hours and then it's off again....
I have tried two different handles I have tried two...

Hi All,

It’s my first time here on this forum. Electric parking brake fault appeared on my Citroen C4 GP 2016 model and stayed for several days. Initially it was intermittent and then became constant fault when you open doors etc. can’t apply parking brakes at all now. After a few investigations and reading through these forums I figured that...

Hello guys i buyed a C4 picasso 1.6 hdi and conected it to delphi and got som faultcodes and wonder what part of things i shall put focus on for geting back the Power for the car ?

the speed is slow like 85-115km/h and the axeleration is superslow

i have tried to do a dpp cleaning ...

the codes i have is:

P1394

P1351

P0299

P0473

P0470...

Have just installed v7.01 on an xp laptop ...
1....my xsara picasso is not on list of vehicles

2...when I clicked xsara I got...erruer de chargement de cellule......what does that mean and what do I need to do?????
Will appreciate some help. It's all a bit baffling..

Hi All
I'm new to this forum, but not to Citroen/Peugeot , I generally do other car stuff, coding programming, Diagnostics, remapping etc. NOT Citroen/Peugeot.

Now Citroen or Peugeot , when they get a Bsi or Engine Ecu Lock immobiliser access, corrupted eeprom, Caused from something as simple as jump starting the car.

I thought i would start the...

Bit of a strange one folks.
On a 4 poster, I lift the xantia up and pull it down, at the bottom of travel there is a knocking/popping sound which is quite distinct and audible. My mechanic said it could be felt through the sphere when touched. It can be heard and felt when driving, almost like a drop link type sound but its at the rear of the car...

Hey guys, long time lurker here. After refueling a few days ago I got the general check engine light on the screen of my 308 T9. It was diagnosed as a faulty additive pump and basically no garage wants to touch it since pairing a new one is a dealer only job, in their words. Dealer quote exceeds a 1000 euros which I find insane. By some googling I...

Hello.

My C5 2003 1.8 Petrol Automatic drives normally without issues but after being serviced at the dealer, I got the Service light and the Check Engine light.

In order to have an idea, I bought an ELM adapter and installed the FAP App, scan codes and received one code P0411 , after some search I found Secondary Air System , so, dismantled the...

Fault Code 1AA0H/6816 REFER TO OEM REPAIR INFORMATION

Hi does anyone have any experience of the iCarsoft Fr V2.0 specifically for Citroen and Peugeot.

I am looking for a diagnostic tool for my 2013 C5 and 2009 C6 to do Electrionic Parking brake, gearbox fluid levls etc.

Thanks
Mark

Hi,

I'm running Diagbox 7.57 in a Windows 7 VM via VirtualBox with a Lexia Rev C interface and USB passthrough. What I find is that I can't diagnose non-starting issues as it only records data up to the point when I crank the engine - as soon as I turn the key, Diagbox complains of losing the connection and asks me to retry or cancel. Likewise,...

Hi I have a fault code P0423 Atomizer for injection of fuel at the exhaust. It showed up today after changing the air intake temperature sensor. My Van has been having a strange problem like a diesel knocking noise but it only occurs when the air temperature is cold ie below 12c. This week has been good to me as the problem had been fine for...

Hello. I'm new here
Recently I bought the token form the PSA service box to using the diagbox. I've got a 2021 C5X witch I think they haven't starting selling in Europe yet I think.

The problem is the latest version of the diagbox (v9.119) doesn't have C5X in the list , automatically detect can read the VIN but says have no permission to...

Hello guys I jumped in my dispatch after it's been stood 2 weeks no crank and I couldn't even connect with my little El cheapo reader that has always connected.
I've got no heater blower no main lights just side lights.
I've tried resetting bsi main lights worked but still no crank and anti pollution on dash cowling for my efforts lol.
Reset...

Hi

Car spec : Citroen C5 X7 2009, 2.0 HDI 140 PS, vin: VF7**************[VIN obfuscated, can be read by forum staff]
This topic has started 2 years ago, with no visible starting point - and it's related with standard error that comes to main screen - anti pollution faulty. I know that there are a lot of similiar topics, but they are considered as one error - one problem. I think that my...

Have diagbox working on a. Chrome book?!

They are so oooo reliable and have no moving parts.

Hello friends, I'm looking for someone from Felixstowe / Ipswich or near with diagbox / lexia who can help me please.
Thank you so much.

I'm still having lexia/diagbox install fun and games.

I got another Windows xp with home edition on it.. Started installing diagbox and it stopped half ways through with a fail to install..

I'm not stuck with a half copy of diagbox but cannot find the dB cleaner anywhere to get rid it all.. I tried dooing an xp pro install but the cd drive...

Hi just installed the lexia software I found on here for my Citroen C4 Picasso.When I plug my actia in the light flashes 3 times then stays on.but my laptop says connected usb device not working.Any ideas

Has anyone here tried FAPlite -android software? Any recommendations on (preferably slim and cheap) bluetooth dongle that works with it?

all, I seem to have broken the access to my Pug diagrams, I am hopeless with Computers :)

It seems the system I bought loads a virtual machine running win XP in it's own window, as an admin, and fires up the documents.. but somehow I have made a change to login, and now cant get back to where I was.
The machine opens as a guest and then doesn't...

Hello,

I get the p0087 code on cold start (after about a min of ideling), car starts studdering (revs dial rotates 100-200 revs up/down) ... High pressure petrol value in this case is low (obd measure). If i shut down and restart car comes back and high pressure stables at around 50bar on idle.

So...am i doomed = faulty high pressure fuel pump?...

I would like to fit a towbar and associated wiring to my 2004 Berlingo.

What is the easiest way I can determine for sure if I have a canbus system?

Thank you

My go to site for OBD info

Dear all ,
Can any one help or has this fault come up .
I scan my car and this code come up p15A4 is c4 grand picasso 2016

Hi everybody. I bought a Citroen Xsara 2 1,6 16v 2002 with light and rain SENSOR. When i bought it 4 years ago, it had problems with lights so i changed the COM2000. After that lights works right. My problem is the wipers never worked fine. I can't tell if it was like this since i bought it, if it was before i changed the COM2000, i think so, but...

Earlier this year I bought a full chip reader from easydiagnostics. For several reasons I've not been ablo to use it until now.
2 discs followed the unit.
First disc with software and update worked fine (well, not tested in car yet, but software starts fine and I can click into car models without fault messages.).
To update further gives the...