French Car Forum

my 1.6 bluehdi 2016 69000 miles, started giving fault code p2448 when in automatic mode getting to 2000rpm loses power and throws a code and uses lots of fuel and seems to hunt a little, so I clear code ok till I get to 2000 rpm and does the same, now when I put in manual mode on gearbox it drives fantastic no fault codes drives as smooth as silk...

I am looking to replace from driver's side shock absorber.
My car spec: 308 ALLURE E-HDI -- 1.6 Diesel Manual 2014
Donor car: 308 BLUEHDI -- 1.5 Diesel Manual 2019
This is what the part looks like: (see attachment please)
Now my question is, will this fit in my car? I am unable to get part number of the donor component and the seller is...

Hi everyone,
I refreshed the fluid of my AMN8 gearbox by already known method of draining around 3 liters 4 times and after that adjusting the level. In some of fhe forums I have read that after changing fluid, oil wear counter needs to be reset with Diagbox.
In Diagbox under repear menu I could not find any option for oil wear counter reset.
Even...

I recently changed the rear discs and pads on my wifes 2012 5008 ... mechanically no problem brakes work fine

I disabled the auto parking brake using a diagnostic tool to allow the work , again no problems
I tried to re-enable the auto parking brake function and i get this is prohibited due to a C155d error , which looking it up says it means...

Hi I am wondering if anyone can help me I have a Peugeot boxer 2019 2.0 euro 6 it keeps coming up with the faults in the photo . I have changed map sensor , turbo boost sensor , engine wiring loom , turbo , all vacuum pipes , egr and throttle body . Any help would be greatly appreciated as it’s about to find out what a can of petrol and a lighter...

Hello, I am having a nightmare with my Boxer 3 Euro 6 2.0 BlueHDi Van and wonder if anyone here can help, please?

I’m new to the forums as a user but have been browsing for a while for advice, and I would like to thank you for all the information that has helped so far. I would be grateful if anyone could help with my issue below, as the garages...

Got a good one to sort out

Peugeot 3008 18 months old.
Driving back through France a couple of days ago, started off OK in the morning with a nice breeze through the ventilation system. Put the aircon on when it got a bit warm everything OK nice and cool.
During the trip up noticed it was getting a bit hot and sticky inside the car, put hand in...

Hi,

New to the forum. I have a 2010 Peugeot expert teepee 1.6hdi. Annoyingly the lower radiator hose burst off while driving and the engine overheated. I have not yet tried to see if it will turn over but I suspect the damage will be extensive and a new engine required. #-o

It has aircon and 90hp. Just wondering if anyone would be able to...

Im having a major problem with my peugeot 306s locking system

This car was lying up for ages and the locking system hasnt been used in years. Today i locked the car and it all worked as it should all 5 doors locked when i tried to unlocked it the central locking didnt do anything and only opened the door i had the key in

Now the 2 back doors and...

Hello everyone.

So we bought this tiny little car for my girlfriend and I did some work on it, but still it has problems. I did some research and found this thread: , I am facing similar problem, but not quite the same.

So after we bought the car, there was an oil leak from chain tensioner. Fixed.
Did an oil change and filters change.
Car was...

2003 (multiplexed) Peugeot 206 automatic.
For a few weeks its been randomly loosing its speedo accompanied by lumpy gear shifts. Got more frequent so ordered and fitted a new output shaft sensor for the AL4 autobox but its made no difference. Any ideas?
oldbill

Hi,
I have problem with my 308 sw 1.6 hdi 120 from 2017, 60k on the clock. While driving, when I press the gas pedal, there is a fast rattling sound, when I release it it disappears immediately, the rattling noise can be heard in all gears, but especially on the highest ones. The noise will only appear while driving, engine runs smoothly, no...

Hi .. a bit of background first

I've had my 2012 207 1.6 HDI 92 from 2013 when it had done 12k .. its now on 85k and regularly serviced by myself as a mechanical fitter.

For some time it has had a nasty smoking habit .. mostly black with a little blue on start up. It gradually got worse and ended up with DPF at risk of clogging message coming...

When the engine gets hot up to 95 to 98 degrees celcius the cooland fan does not start.
where is this on the engine
Any one have a sceets or a picture of where its located on the engine ?

problem solved...

This is the colour of my coolant... looks muddy... Thought it was supposed to be a vibrant colour.

I have not noticed unusual car temperature or performance decrease but this has caught my eye.

Hello friends,
PP 1,9D WJY VF3**************[VIN obfuscated, can be read by forum staff].
After starting the car drove normally. After a while after adding gas, the needle of the tachometer and coolant temperature dropped and the engine started knocking. After a while, the tachometer needle and the engine temperature started working and it drove normally. Then the problem recurred. When the...

Hi
I have a 2010 peugeot boxer LWB and my passenger side window will not go up or down
anymore i have replaced the window motor and still no joy , the motor gets hot and there is power to it
all the time , I have found out that relay R4 on the fuse box operates the drivers side window and mirrow
does it control the passenger window , and could...

Hi

I have a 2010 3008, the boot has all of a sudden stopped unlocking therefore I cannot open it. The fob and the interior unlock button doesn't open it. Is there any way I can get it back open? Is there a fuse that may have blown preventing the solenoid from working?

Hi,
I have two 308 t7 and both by VIN number have ELECTROCHROMATIC DAY-NIGHT INTERIOR MIRROR but they are quite different!

On VF3**************[VIN obfuscated, can be read by forum staff] there is one sensor in front and one on the back, no buttons:

IMG_7961.jpeg

IMG_7962.jpeg

On VF3**************[VIN obfuscated, can be read by forum staff] there are TWO sensor in front (why?!?) and one in the back and one button:...

Hi

Car was running great on highway and then went into limp mode / cruise control error and MIL light

Diag is showing P0088 fuel pressure is higher that reference value 361 bar / 36100 kpa psi v 282 bar / 28200 kpa reference value at 1216 rpm and P0087 regulation of fuel pressure is lower that reference value 760 bar / 76000 kpa v 941 bar /...

Hi
I am seeking to clean a few things in my engine, namely: the glow plugs, the inlet manifold, and fuel injectors.
To do this, it appears I need to remove a very solid metal bar/cylinder over the engine that I believe is some airflow (after the turbo?) cylinder.
Can someone help answer: can I remove this and then how? I have unscrewed the hose...

Is it possible to order this puddle light as a standalone unit? I don't mind if it's aftermarket. See attachments please.

Thank you in advance.

Hi,
can somebody tell me what this “grill” is for?

It looks like some kind of air sensor…?

IMG_7921.jpeg

Hey guys I’m looking for some advice.

I have a 2017 Peugeot Boxer Euro 6 2.0 Blue HDi 130 (96kw / 130cv).

Last year my partner and I converted this to a camper and spent 3 months on the road in Europe. At the end of the trip we started getting trouble with out DPF and kept going into limp mode. We cleaned the DPF when we got home and it’s been...

Anyone know if the Lexia-3 interface can tell which plug is misfiring?

Also are there any settings in the ECU which can be configured differently such as strenght of spark?

hi,
I had urea light came up in my car and I have refilled with AD-Blu additive but the light is still on
Plz advise what to do?

17148493089091982504161075341036.jpg

Is there a guide, if any kind, available that shows how to remove the speakers in the RCZ that are fitted in the side panels by the rear seats?

-Andy.

Brake pedal has just sunk while braking and there's fluid leaking below the rear drum. I haven't looked properly but I'm assuming the rear wheel brake cylinder has failed. Checking prices for cylinders and shoes I noticed they were available for vehicles either with or without ABS. This has confused me as after looking under the car once when it...

207 1.4 vti same engine as mini

i noticed my gearbox is making a click noise when around 1.500-2000rpm when slowing down or running at that rpm when driving

its not driveshaft as soon as i press the clutch its quiet or put in neutral

is there a chance the gearbox is going to shxt itself if it starts to get more louder at min you can hear it...

Pls help 🙏 I looked everywhere my peugeot 3008
Got 3 fault cods 040A,04D3,0EB3
I know that first one is oil level,second I believe additive fluid but 3rd one no idea
I watched on YouTube one guy and he ben saying that pump for additive tank got fuse but I don't have idea where I should search for it coz I don't know if pump works or not I got...

Good morning all,
I have a 2010 Peugeot Boxer which I purchased as a non runner. I originally thought it was a timing issue as there was no sync between the cam and crank. Having changed the chain (although the timing was perfect anyway) it’s still the same. It now appears there is no comms to the BSI, however we did get it communicating for a for...

206cc Roof acting like a stroppy teen.

My 206cc was parked up just before the mot expired & sorned for the winter. I did run it up a few times to keep the engine lubricated but didnt lower the roof enough times due to some rubbish weather & life getting in the way. Last week on a dry but chilly afternoon i started the car & thought lets put the...

Hi all
My boxer rear doors keep flapping about in breezy conditions when opened at a 90 degree angle
Was wondering if the rear door check strap hinges are any good for preventing this as mine hasn’t got any fitted but there are mounting points for them to be fitted ?

Many thanks

Steve

Hi all,

I couldn’t see an answer to my query, so if it does exist, apologies,

I’m looking to access the engineering mode on our 5008, to enable the entertainment system to use a usb hub. There is one code mentioned quite a few times on the web, 7503900. However I’ve had no success with this number. Would anyone have a different code that I could...

Hi all, apologies if this is a stupid question...

The other day my dad's 307 wouldn't start. Immobilised. Did some electrical investigation in the car (its very damp :)) but to no avail, then had the key on the bench and turned out it just needed some TLC! Soldered on some new passives to the PCB where the issue was, re-initialized the key and...

I've just acquired a tatty and unloved 208 for my son. It does start, but the idle is really lumpy and the accelerator does absolutely nothing, no response at all.

I'm also a bit suspicious that the fan continues running after switch off. I'm not quite sure why, as the engine is not hot, and the dash temp guage reads still pretty low.

I havent...

Hi. Looking for recommendations for an upgrade over stabdard/oem waterpump.

Im after one with a metal impeller (plastic ones known to fail for some). It's hard to find this listed in specs of most I've found online.

Anyone got first hand experience or share any links to one?

Thabks

Hello all, thanks for your time.

I have just inherited a 2013 Peugeot 208 XY E-HDI and have an engine fault on start. It starts and ticks over fine, theres no rough idle or anything. The car had been sitting for 6 weeks or so but did start up fairly easily. Someone who knows the car said it was being driven with this fault for a while but i need...

I have an unknown pipe running from a T-piece where the oil breather goes into the inlet manifold. This goes down behind the engine, runs along the bulkhead and through a hole into the inner-wing/suspension turret but can't see where it goes from there.

Anyone know what this is and where it goes to?

Hi all,
My 308SW (2017) has developed the common battery/charging/all systems fault that seems to be due to a failing relay in the BPGA (part 9675350280).
I've watched a video that shows that replacement is simply a straight swap over.
However, two potential suppliers of the (expensive) part tell me that it has to be programmed and I'll need to...

So I have a 207cc with dual zone climate control which is, quite frankly due to the size of the cabin, ridiculous.
Getting fed up of having to adjust the temperature on both knobs.
Is there any way of putting the thing into a 'mono' mode?

Does anyone know why all of sudden my indicator is making this sound instead of the typical relay sound? this happened when I left my car's ignition on for too long because it wasn't doing it before that... I don't know how to revert this change... please help!

Hi all,

After almost a year of trying to resolve some issues with my 3008 with a 1.6l diesel (and a lot of time and money spent), I’m getting to the point where I just don’t know what to do anymore. We keep trying to get the car ready before going on a family holiday, to be told it’s fixed, and then inevitably there will be a problem. If anyone...

I was changing the gearbox oil and thought that the bolt with the red circle is the filling plug but after a few turs it felt wrong. Then I screwed it back. And filled the oil through breathing hole. My question is what this bolt is for and if a few turns out wouldn't make anything serious loose inside the gearbox.

The car ir Peugeot 5008 2018....

Good afternoon,
I have a 1998 106 1.1 Zest 3 which, I believe, has the TU1M(HDZ) engine with the Bosch fuel injection. A couple of months ago two issues manifested:

1) The engine misfired when accelerating
2) The idle speed would drop to 500rpm or the engine would stall completely.

Issue #1 was fixed with new spark plugs and HT leads.

Issue #2...

Hello.
Could someone advise me please on the programming injectors for the Peugeot 3008 2011 with ICarsoft CR PRO. The issue is that after I have renewed a new injector, I faced an issue with the Diagnostic tool: Application failed .
In fact, in the Injector menu I have two options:
1) Classification of injector.
2) Replacement of injector.

If I...