Common Problems & Fixes - Archive

Moderator: RichardW

49 topics • Page 1 of 1

Announcements

Statistics

Last post

Forum server settings changed

by xantia_v6 » 07 May 2024, 19:01 » in Forum News, Announcements and Issues

First post

Due to excessive server loading caused by some badly behaved 'bots' (automated content collectors), I have changed the anti-ddos settings on the site to be much more aggressive.

This has had the desired effect of reducing the server loading from 100% to about 10% (the other 90% was coming from just 8 IP addresses located in China).

There may...

Last post

I have been keeping an eye on the server performance, and the every 5 minutes same addresses would flood the forum with requests for a few seconds before getting blocked again.

In the last hour they seem to have got bored and gone away.

Replies: 5
Views: 165

Last post by xantia_v6
08 May 2024, 10:30
PSA Electrical Diagrams - Wiring & Symbols Codes Index

by GiveMeABreak » 09 Dec 2023, 17:48 » in Diagnostics

PSA Electrical Diagrams - Wiring & Symbols Codes Index

The following will cover most basic equipment, but will exclude later systems & Tech.

PSA Electrical Diagrams Introduction - Function and Constitution of Codes
PSA Electrical Diagrams - Coding of Functions
PSA Electrical Diagrams - Component Coding
PSA Electrical Diagrams -...

Replies: 0
Views: 37058

Last post by GiveMeABreak
09 Dec 2023, 17:48
Citroen, DS Automobiles and Peugeot Official Part Number Requests

by GiveMeABreak » 15 May 2021, 13:55 » in Citroën
1

…

134

135

136

137

138
First post

Please make all your Citroen , DS Automobiles or Peugeot Parts Requests on this thread

This thread is only for donating members who wish to request official part numbers or Parts Diagrams.

Please don't post technical queries or ask 'how to' questions here. Create a thread in one of the main Citroen / Peugeot Forums for these queries....

Last post

71 is bolt M6 x 1mm x 20mm (part no 692395 @ £1.46).
18 is the clamp, part no 1714R4 @ £10.73
Replies: 2058
Views: 688980

Last post by RichardW
05 May 2024, 17:57
Airbag, Dashboard, Seat Belt & Airbag ECU Repairs

by GiveMeABreak » 24 Jun 2020, 17:01 » in Useful links
1

2

3

4

5
First post

Just for members to be aware that airbagteam.com based in the UK are offering a 10% discount to FCF members on any of their services.

The FCF does not endorse any company directly, but thought this would be of use to members.

Full details of their services and the discount can be found here:

Airbag, Dashboard, Seat Belt & Airbag ECU Repairs

Last post

Re the 407 door seal issue and airbag warnings, after a few days of rain and testing with the hose, I gave up as water was still pooling on top of the bottom door seal and then running inside the car.

My solution was to put a few holes thru the seal with a leather hole punch tool which seems to allow the water to exit (the door seal gets squashed...
Replies: 64
Views: 82394

Last post by 407
07 Mar 2024, 23:42
Important Information concerning access to PSA parts data

by xantia_v6 » 19 Mar 2020, 04:19 » in Forum News, Announcements and Issues
1

2

3

4

5

6
First post

As some of you may already have realised, PSA (Citroen, DS Automobiles & Peugeot) have this week (from 16/03/2020) decided to close off free access to parts information.

The public version of PSA's ServiceBox, which is the official source for parts and information has had a freely accessible parts system for registered garages, and individual...

Last post

Please note: This Thread is now Locked.

Please Make All Your Citroen or Peugeot Parts Requests Here

All parts requests from this topic have been moved there.
Replies: 88
Views: 122070

Last post by GiveMeABreak
14 Nov 2021, 07:21
New PSA Heritage Parts for Classic Cars

by GiveMeABreak » 11 Oct 2019, 16:18 » in Citroën

First post

Parts for Classic / Older Citroen, Peugeot Renault Vehicles

This may be of interest to Members with older vehicles where getting parts is a struggle and for those not already aware of the site.

PSA are embarking on a project to provide some supplies of original and re manufactured parts for older vehicles and classics, and have made it a...

Last post

I'm trying them for anything showing up as NFP now.
Sometimes hit lucky.

Replies: 3
Views: 35607

Last post by white exec
24 Jan 2020, 16:49
Revised Easydiagnostics Discount Procedure

by GiveMeABreak » 03 May 2018, 17:22 » in Forum News, Announcements and Issues

Please note that there is a new procedure in place for members wishing to take advantage of a 15% discount off products from Easydiagnostics.

The old discount code that was entered into the checkout is no longer valid, as a result of the code being propagated over the Internet.

After discussions with Jim from ED today, we have agreed a new...

Replies: 0
Views: 37910

Last post by GiveMeABreak
03 May 2018, 17:22

Topics

Statistics

Last post

C5 2.2 HDI Mk1 Definitive Diesel Additive Low Level Warning Solution

by howardaskew » 07 Jan 2017, 14:18

First post

My wife's 2.2HDI C5 Mk1 2004 Exclusive Automatic gave the diesel additive warning a few thousand miles before 100k.
We continued to drive it for well over a thousand miles before I finally tackled it. I was armed with a Eolys refill kit and 1 litre of Eolys 176 (green).

You read posts that suggest that the Eolys additive is not being added as...

Last post

The pictures were most probably hosted on Photobucket and they imposed charges for images linked to websites. Lots of us withdrew from Photobucket then.

Replies: 3
Views: 9681

Last post by myglaren
05 Jul 2023, 14:15
C5 Tourer 2009 Electronic Handbrake MOT issue

by NAM » 18 May 2017, 20:54

First post

Hi All
It's been a while since I was on the forum but I could do with a bit of help. My 2009 C5 Tourer has failed its MOT as the handbrake is not doing its job properly.

The cable at the caliper end seems to be sticking too far out so when the unit engages there is insufficient pull.

The options discussed with me by the garage are to either...

Last post

Ok Marc,it's not a big job to check the cable spacer on the EPB. As I said I haven't actually replaced mine, but I've just had a quick look and should only take 10mins.

Procedure to inspect and replace EPB spacer C5 x7
1) Suspension to high ( hydractive model)
2) Chock front of car
3) Jack up and remove rear road wheel
4) Handbrake to off -...

Replies: 7
Views: 8102

Last post by petef
20 May 2017, 16:42
Citroen Xantia Power Steering Pipe Repair Kit.

by mardybum » 31 Jul 2014, 10:28

First post

Up for your delectation today, we have a CUSTOM designed and made replacement for the Power Assisted Steering Hose on the Citroen Xantia.

I purchased the car, knowing it needed work. The previous owner had been quoted in the region of £500, 2 days, and that wasn't a guaranteed fix either. It took a few £££'s to get it right, and arguing with the...

Last post

May I be the first of many Xantia owners to congratulate and thank you =D> =D> =D> =D> =D> =D> =D> =D> =D> =D> .. I'm sure you will have almost every Xantia owner on the forum making a huge sigh of relief knowing that their cars won't have to be scrapped due to a fairly simple pipe replacement.
My order (its worth it for the just in case factor)...

Replies: 1
Views: 5910

Last post by c.morewood
31 Jul 2014, 10:47
The Xantia internal fan riddle.

by alan s » 03 Mar 2007, 19:59

As discussed:

With thanks to all who contributed.

Alan S

Replies: 0
Views: 21521

Last post by alan s
03 Mar 2007, 19:59
How to hydraflush a Xantia

by alan s » 14 Jan 2007, 20:51

Refer here:

Cheers,

Alan S

Replies: 0
Views: 18131

Last post by alan s
14 Jan 2007, 20:51
Xantia ABS testing.

by alan s » 03 Dec 2006, 19:18

Rather than break the thread or shift it, here's a link to a thread in the Citroen forum regarding testing when the ABS warning light stays on. It also includes pin outs for the test.

Thanks again to those who have contributed.

Replies: 0
Views: 17609

Last post by alan s
03 Dec 2006, 19:18
Coolants, stray currents and corrosion

by alan s » 17 Jul 2004, 05:40

First post

I was getting a new muffler on one of the cars the other day and whilst there found a brochure relating to the topics of this post.
It was a re-run of an article attributed to NRMA Tech Topics Bulletin 1/98 and whilst it's long & involved, I'll try to summarise it here as it may answer a lot of questions associated with the problems we get on...

Last post

An update on this info;
Check out pages 3 - 4 - 5 - 6 of this write up by a coolant manufacturer.

Much of what has been printed above is there plus more and up to date materials including their latest coolants.

Alan S

Replies: 1
Views: 18914

Last post by alan s
26 Oct 2006, 21:31
Noise from the aircon pulley.

by Kowalski » 26 Jul 2006, 16:06

First post

I've got a bit of a rattle from my air con compressor, only when the air-con is off, it disappears completely when I turn the air con on. I thought I'd better fix it before the pulley drops off!

I'm guessing that the idle bearings in the pulley are dead or dying and need replacing. I've got a Sanden manual that suggests the pulley is easy enough...

Last post

More information, I've found a couple of sites with useful information.

Firstly, this site lists parts, it has a bearing interchange list.

Secondly, this is a guide written by somebody who has replaced a clutch / pulley assembly because of a dodgy bearing. He bought the correct tools rather than machining his own!

It would have been nice to...

Replies: 10
Views: 23846

Last post by Kowalski
02 Aug 2006, 16:43
Ticking steering wheel on Xantia (sounds like trafficators)

by alan s » 26 Apr 2006, 21:03

From a previous posting which offers a solution to the mad ticking that some Xantias get that seems to eminate from the steering wheel area.

Alan S

Replies: 0
Views: 17672

Last post by alan s
26 Apr 2006, 21:03
Xantia components photographic reference.

by alan s » 20 Apr 2006, 00:22

With thanks to member deian for his efforts on this.

To use, click on thumbnail of pic you wish to see. When enlarged, this will bring up a series of boxes in some photos. When the cursor is run over the inset boxes, a description of the part will pop up.
Handy when trying to identify parts when doing repairs.

Alan S

Replies: 0
Views: 18430

Last post by alan s
20 Apr 2006, 00:22
Hydractive information

by alan s » 22 Aug 2005, 03:48

Courtesy of sbraud the technical manuals for the Hydractive 1 and 2 series:

quote: Citroen Technical Training - Consultant Technician Module B7 Hydractive I and II systems for XM and Xantia”

Replies: 0
Views: 18456

Last post by alan s
22 Aug 2005, 03:48
BX autos; why do so many fail?

by alan s » 02 Jul 2005, 15:08

This week I've had my first opportunity to take a decent look at and become a little educated on the ZF auto in these cars.
It has always been said that the ZF auto was considered bomb proof in the CX yet in the lighter BX it has had all kinds on things said against it; granted not the same box, but rarely does a manufacturer go from a quality...

Replies: 0
Views: 18420

Last post by alan s
02 Jul 2005, 15:08
Reprogramming Plip on 94 Xantia

by alan s » 03 Jun 2005, 04:00

Referring to a topic from the Citroen forum

Alan S

Replies: 0
Views: 17835

Last post by alan s
03 Jun 2005, 04:00
Fitting new heater matrix to Xantia.

by alan s » 13 Apr 2005, 04:27

Our acknowledgements to peteev for the excellent detailed description of the job detailed below.
I left the 1995 1.9TD Xantia whilst I went off on holiday. On returning to the car there was a musty smell and some bright blue globules of water running down the heater outlets onto the carpets but worst of all the clouds of moisture deposited all...

Replies: 0
Views: 18340

Last post by alan s
13 Apr 2005, 04:27
reprogamming Xantia VSX keypad

by alan s » 27 Feb 2005, 04:24

First programming:
Ignition on.
1 Enter the code 0001
2 Press key C
3 Enter your personal 4 figure code.
4 Press C key to validate.
Four flashes of the green warning lamp and four audible beeps indicate the information is recorded.
************************************
To Change the code:
Ignition switched on
1 Enter your old code already in...

Replies: 0
Views: 17693

Last post by alan s
27 Feb 2005, 04:24
Retro fitting air/con

by alan s » 19 Feb 2005, 02:33

Here's a link to a (long) detailed write up on the fitting of air/con to a series one BX16V.
The things we learnt along the way can be used as a guide to anyone retro fitting air/con to any make or model as a lot of the traps are universal.
It should be remembered also, that by trade I am a refrigeration and air conditioning mechanic with many...

Replies: 0
Views: 17539

Last post by alan s
19 Feb 2005, 02:33
BX belt adjustments; stopping the squeals.

by alan s » 14 Feb 2005, 09:52

If you've ever replaced an accessory belt on a BX with air/con, you'd know the high pitched squealing that usually follows this, caused by belt slip.
It is particularly common on 16Vs and it usually ends with someone declaring it's a faulty belt or something else has gone amiss. Here's the procedure that should sort it out.
Slacken the top bolt on...

Replies: 0
Views: 17184

Last post by alan s
14 Feb 2005, 09:52
Refurbishing Fuel injector nozzles.

by alan s » 12 Feb 2005, 07:26

Just did the injectors over on the TZi but the same applies to the 16V.
Kits are available (includes enough gear to do 2 nozzles) which cost around $10.50 a set, so for about $21 and say an hours time, a full revamp of the injectors can be done. This includes filters to fit in the nozzles, O rings and end caps and makes one real big difference to...

Replies: 0
Views: 18221

Last post by alan s
12 Feb 2005, 07:26
Swapping rear rotors and bearings on a BX

by alan s » 06 Feb 2005, 02:12

Had to do a rush job on a BX that came from the UK.
A rear wheel bearing had collapsed following the seal backing having rusted out due to salt contamination. This of course caused the seal to totally collapse and leave the bearing open to a variety of foreign substances such as moisture and grit.
The result was that the inner cone had become...

Replies: 0
Views: 16609

Last post by alan s
06 Feb 2005, 02:12
Rebuildng Xantia fan motors is possible.

by alan s » 10 Dec 2004, 14:06

O.K. I admit it; I'm cheating here, but I asked a question on a board and then answered it myself, so I'll do this in two parts; ask the question (just like most do when they look at what seems to be a Mission Impossible ) and then I'll give a detailed answer.
I'll try to edit out some superfluos banter if possible without losing the content....

Replies: 0
Views: 17950

Last post by alan s
10 Dec 2004, 14:06
Rear arm bearings; the permanent fix.

by alan s » 03 Nov 2004, 03:00

The bane of every BX owners life seems to have been these rear (swing) arm bearings. Few have mamanged ownership over any amount of time without having to do them, some more than once.
The symptoms: When the car is set at its highest suspension position, the rear wheels when viewed from about 20 feet away look like this / \ or ! \.
Creaking...

Replies: 0
Views: 21202

Last post by alan s
03 Nov 2004, 03:00
BX steering pinion seals replacement.

by alan s » 13 Jun 2004, 14:31

After putting up with the green drips on the driveway whenever the car was parked long enough to allow the suspension to settle, it was decided when the clutch cable carked it that now was as good a time as any to fit the seal kit to the steering pinion.
An examination showed that the problem extended further than the seals too with the steering...

Replies: 0
Views: 16746

Last post by alan s
13 Jun 2004, 14:31
BX front struts- yet another cure...

by Bob Smith » 04 May 2004, 19:28
1

2
First post

As these pipes already contain LHM I don't see how the ride can be improved, unless of course it's feature of new LHM like the short lived non-sinking rear end when the LHM is replaced.
Bob

Last post

Lower the suspension fully, remove the vent pipes from the strut and immerse the cleaned ends in a jar of LHM. Select maximum height.
Replace the vent pipes. This method lubricates the inside of the strut. The ride is transformed and it will last longer than greasing the outer strut shaft.
Replies: 20
Views: 38454

Last post by tomsheppard
04 May 2004, 17:42
Solution to Starter Motor problem

by alan s » 28 Mar 2004, 04:44

Here's a copy of a posting I've put on an Australian Citroen site (mainly because BXs are still fairly *new* by our standards) but one I feel could also be of interest to any Cit & possibly some Peugeot owners. It concerns the lazy starter syndrome and a cure for it.
**********************************************************************
A while...

Replies: 0
Views: 17761

Last post by alan s
28 Mar 2004, 04:44
Fitting & routing a BX speedo cable.

by alan s » 18 Mar 2004, 14:40

Before you start, disconnect the speedo cable under the bonnet at the junction of the upper & lower speedo cables to confirm whether it is the upper or lower cable that is broken.
In most cases it seems the upper cable (the top one) is the most likely culprit.
Remember: There are no shortcuts in this job!
To access: Remove the tray near the...

Replies: 0
Views: 16775

Last post by alan s
18 Mar 2004, 14:40
Brake Pipe Tip

by Jon » 19 Feb 2004, 19:12

Here's a tip that I have found useful when assembling/dis-assembling brake
pipes and unions.
Before tightening up a rigid brake pipe union, carefully smear a small amount
of copper based anti-seize compound around the brake pipe BEHIND the flare. I
have found that this stops the sort of corrosion that can seize the union to
the pipe and thus...

Replies: 0
Views: 17985

Last post by Jon
19 Feb 2004, 19:12
Top end rattles/oil pressure loss on 16V engine

by alan s » 16 Feb 2004, 03:01

As many know, a while back my son did a rebuild on the BX 16V series one (160 BHP) engine. Everything was done by the book & only the best of the best went into that engine & only very competant tradepeople worked on or oversaw what was done. It should have been as close to perfect it was humanly possible to get!!
On completion, it was even given...

Replies: 0
Views: 11641

Last post by alan s
16 Feb 2004, 03:01
A word of warning to hydraulic Cit drivers.

by alan s » 12 Jan 2004, 10:28

Below is a copy of a posting from one of our members LHMleak about an incident that happened to him recently in his Xantia with anti-sink.
As a BX & CX driver, I would never have thought of this just as he didn't; red light comes on indicating low LHM, not far to go, car stays up so it should still have brakes & steering is exactly what I would...

Replies: 0
Views: 9110

Last post by alan s
12 Jan 2004, 10:28
Xantia Clutch cable problems

by alan s » 01 Jan 2004, 07:18

A thread on this subject complete with pics that should be of help to all those Xantia owners who have gone beserk in the past rying to solve this one.
Alan S

Replies: 0
Views: 7256

Last post by alan s
01 Jan 2004, 07:18
Coolants & corrosion

by alan s » 02 Oct 2003, 05:17

We often get requests on the forums for advice relating to why certain cars radiators or the heater matrix seems to be continuosly rotting holes in themselves.
It has been blamed on the salted roads in winter causing corrosion from the outside in and in some cases this is possibly a reasonable explanation, however, even that problem can be...

Replies: 0
Views: 7073

Last post by alan s
02 Oct 2003, 05:17
Mayonnaise in Oil breathers.

by alan s » 01 Oct 2003, 03:48

I reckon you guys over there should refer to the period of time between about September & April as Salad Days; everything seems to be swimming in Mayonnaise
It doesn't have to be a blown head gasket, in fact in most cases it's not!
It is usually moisture contamination of oil vapour in the breathing system caused by condensation. The condensation...

Replies: 0
Views: 7472

Last post by alan s
01 Oct 2003, 03:48
Exhaust Valve guide replacement

by alan s » 11 Aug 2003, 18:10

This has been taken (on the authors authority) from another board.
It related to a job done by this guy & using Gerry, a Morgan rebuilder as a mentor & assistant when doing the job.
It was done on the head of an 8 valve BX Gti, however, the principles used would be applicable to other engines in the range.
Some time ago I mentioned in this Forum...

Replies: 0
Views: 6496

Last post by alan s
11 Aug 2003, 18:10
Freeing corroded parts

by alan s » 06 Aug 2003, 05:33

We often get postings from people having problems loosening parts that have corroded in and predictably, these all too often all end up in tears when something like a brake bleed nipple sheers off in the caliper or a rear sphere is so tight that the rear cylinder turns & takes out all the plumbing in the process. As a former tradesman working on...

Replies: 0
Views: 9504

Last post by alan s
06 Aug 2003, 05:33
Data on Xantia Electric Door Locks

by Jon » 16 Jun 2003, 20:32

Written by David Goddard
Some information of the wiring of door locks (with deadlock facility).
The electrical connector has 5 pins. Call the highest pin No.1.
Normal Lock Circuit:
Uses pins 1 and 2. The resistance across pins 1 and 2 should be about 5ohms if the coil is OK.
If OK, applying 12V+ to pin 1 and negative to pin No.2 will unlock....

Replies: 0
Views: 6693

Last post by Jon
16 Jun 2003, 20:32
XM Window Reg Repair

by Jon » 13 Jun 2003, 14:22

Originally posted by Noz
annanoverone
Apparently a common fault on all series 2 XM's is the window winder mechanism failure. Having compared a series 1 to a series 2 it makes you wnder about Citroen sometimes. The series one has a nylon pulley to and bottom which carry the guide wires which are approx 2.5mm dia. On the series 2, presumably to...

Replies: 0
Views: 5991

Last post by Jon
13 Jun 2003, 14:22
XANTIA RIDE HEIGHT

by Jon » 23 May 2003, 14:34

Originally posted by AndersDK.
The Xantia suspension height settings:

Above picture (+ other good stuff) found here :

Thanks and repect to those people and to Anders for finding it.

Replies: 0
Views: 8513

Last post by Jon
23 May 2003, 14:34
205/309/306/ZX/XSARA REAR ARM BRGS

by Jon » 25 Feb 2003, 13:42

Originally posted by Dave Burns
RE: Replacing the internal & external rear arm bearings on 205,306,309 Zx and Xsara
You will need a 12mm x 1.5mm bolt with around three inches of thread on it to drive into the splined bracket and disengage the anti roll on one side, a slide hammer with an M8 coupling to withdraw the torsion bars, then you will...

Replies: 0
Views: 6996

Last post by Jon
25 Feb 2003, 13:42
Citroen ZX: Replacing Dashboard Lights

by B_Draper » 17 Jan 2003, 06:13

You may want to wait until all the bulbs have virtually blown, but that would obviously be illegal for night driving! It would be easiest to change all the bulbs at the same time. Off the top of my head, the basics for the dashboard lights are:
1. Remove the torx screws holding the dashboard controls in place and remove the Hazards/Foglights/Rear...

Replies: 0
Views: 8163

Last post by B_Draper
17 Jan 2003, 06:13
Fault Codes: Bosch Motronic ML4.1

by Guest » 31 Dec 2002, 16:10

BX 16 Valve 87>92 (xu9j4 D6C engine)
11 end of fault code output
12 start of fault code output
14 coolant temp sensor
15 fuel pump circuit
21 throttle position switch (at idle)
22 Idle speed control
33 Airflow sensor (flap)
35 Throttle position switch (full load)
53 battery supply voltage to ECU
54 ECM failure
55 CO Adjuster (part of airflow...

Replies: 0
Views: 7125

Last post by Guest
31 Dec 2002, 16:10
Fault Codes: Bosch Mono Jetronic A2.2

by Guest » 31 Dec 2002, 16:05

Monopoint injection fitted to AX 1.4, ZX 1.4
11 end of fault code output
12 start of fault code output
13 Air Intake temp sensor
14 Coolant temp sensor
21 Idle switch- Throttle Control motor
31 Lambda sensor signal
32
33 Throttle position sensor
41 No engine RPM signal (crank sensor)
51 Lambda sensor signal
52
53 Battery supply voltage to ECM
54...

Replies: 0
Views: 7643

Last post by Guest
31 Dec 2002, 16:05
Fault Codes: Bosch Motronic M1.3

by Guest » 31 Dec 2002, 16:01

BX GTi 90>, BX 16v 91>
54 ECM failure
15 Fuel pump circuit/relay
34 Cannister Purge valve solenoid
33 air flow sensor (flap)
52 Lambda sensor signal
42 Injectors
51 Lambda sensor signal
32
31
53 Battery voltage supply
41 Crank Sensor
13 Air temp sensor (in airflow meter)
21 Throttle position switch at idle
35 Throttle position switch at full load

Replies: 0
Views: 6483

Last post by Guest
31 Dec 2002, 16:01
Fault Codes: Bosch MP3.1

by Guest » 31 Dec 2002, 15:56

As fitted to XM 2.0, AX GTi etc
12 Start of fault code output
11 End of fault code output
54 ECM failure
22 Idle speed control
33 MAP sensor
52 Lambda sensor
22 Idle speed control
51 Lambda sensor signal
53 Battery supply voltage to ECM
41 Crank sensor
13 Intake air temp sensor
14 Coolant sensor
21 Throttle position sensor

Replies: 0
Views: 6472

Last post by Guest
31 Dec 2002, 15:56
Citroen: Resetting service indicator

by Guest » 15 Nov 2002, 19:11

Button is to the right of lower part of speedo
Press and hold in button, turn igntion on.
Keep button pressed in for 5 seconds then release.
Turn ignition off.
Turn ignition back on and Spanner symbol should illuminate for 5 seconds.
Turn igntion off. Job done.
Applies to Berlingo, Saxo; Xsara, Xantia with service indicator in dash display.

Replies: 0
Views: 7442

Last post by Guest
15 Nov 2002, 19:11
Citroen ZX: Replacing rear subframe mounts

by Guest » 16 Sep 2003, 02:25

First post

Finally got round to doing my ZX rear mounts yesterday at 121,000 miles.
See the Common Problems and Fixes section for more details on this, and in particular the wise words of Dave Burns.
I was very lucky that I was able to do this job on a 2 post ramp and used a hydraulic gearbox stand to support/lower/raise the rear beam, together with a step...

Last post

Posted By Dave Burns with additions from JW
Car has to be supported with stands at the rear jack point's on the sill's, use a piece of thick plywood between stand and sill.
Remove spare wheel cage, pull rubber silencer mountings off (washing up liquid helps them slide off) and rest silencer on something suitable, there isn't enough movement...

Replies: 1
Views: 8929

Last post by Guest
15 Nov 2002, 18:02
Citroen ZX: Replacing heater panel bulbs

by Guest » 15 Nov 2002, 16:50

Originally posted by B Draper
I found I had to take off the following in this order - I may be wrong in places as it was a while ago!
Leg Side vents next to centre console,
Ash Tray - there are bolts behind this,
Centre Console around handbrake,
Radio - you'll need to disconnect this,
Unit comprising of the centre airvents above the radio down...

Replies: 0
Views: 7665

Last post by Guest
15 Nov 2002, 16:50
Citroen BX: Fixing slow starter motor

by Guest » 15 Nov 2002, 16:35

Courtesy of Alan Smith
With the miles many BX's have now travelled, particularly those in City areas may find that the starter motor is tending to become slow & at times particularly in cold weather may not always want to spin the engine fast enough for it to start. If this slow turning is accompanied by a grinding sound, there is a better than...

Replies: 0
Views: 6581

Last post by Guest
15 Nov 2002, 16:35
Citroen: Rear Arm Bearing replacement

by Guest » 15 Nov 2002, 16:34

This is courtesy of Y. Narabayashi from Japan.
SUSPENSION Rear Arm
Maintenance Menu
Remove Rear Arm and replace Arm bearing
Rear suspension of Hydro-pneumatic Citroen, includes BX, use trailing-arm system. Pivot shaft of arm sets on the subframe by through the roller bearing.
All successive hydro-pneumatic Citroen adopts this bearing;however,...

Replies: 0
Views: 7341

Last post by Guest
15 Nov 2002, 16:34
Citroen: How to change Rear Spheres

by JohnD » 27 Dec 2002, 23:33

First post

A few notes on changing the anti-sink sphere on a Xantia. Have the rear wheels on ramps, otherwise you won't have room to move. Loosen off the 9mm pipe union leading into the sphere before moving the sphere itself, otherwise the pipe will break. Do less than a quarter turn on both before depressurising. When fitting the new sphere, enter the union...

Last post

Courtesy of Alan Smith.
The rear spheres have to follow a set procedure to change.
Firstly; Set the suspension right to the highest setting (the one used for wheel changing)
VERY IMPORTANT: If the vehicle is not being worked on over a pit, you MUST - repeat MUST put axle stands in a position so that they will stop the car from falling on you if...

Replies: 1
Views: 10769

Last post by Guest
15 Nov 2002, 16:33
All vehicles: Losing/blowing out coolant

by rabenson » 17 Nov 2002, 16:43

First post

My Wife was barreling up the autoroute in her BX19D (j-plate) to catch a ferry. she parked up at the port then, on returning to the car, found that there was a fair quantity of coolant dumped underneath.
Obviously concerned, she (after a suitable period) checked the coolant level and found it to be very low. Topped it up and was escorted to the...

Last post

Courtesy of Alan Smith.
There are a myriad of causes for this problem (ie) cracked head, incorrect timing, blocked radiator, blown head gasket, partial blockage of the cooling system, collapsing hose due to age/deterioration on the intake side of the water pump.
Before assuming the worst, always check for air in the system. Air trapped in the...

Replies: 5
Views: 9505

Last post by Guest
15 Nov 2002, 16:31

49 topics • Page 1 of 1

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum