French Car Forum

Good morning

This code and the text in the attached pic popped up this morning, car seems to drive normally.

What should be the protocol for this code?

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]
IMG_20240218_095131.jpg
Thanks

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]**************

Hello,

I had a P11A3 fault code (i put up a post a few days ago) and it disappeared after replacing the VVT solenoid (stupid engineers, took me hours...) but this P0010 code popped up (and check engine light is on - i can't earse the fault, it is defined as permanent ).

The car seems to run fine , maybe...

I have a Peugeot 207 sportive 2011.
The right hand window control needs replacing. Some sites say part 6490EJ. Others say 6490EH.
Just wondering if they will both work or if there is one to choose

Hi everyone, I'm new here

I have a 2010 peugeot partner with an oil leak, I have located it to be coming from the manifold seal between 2 injectors.
I've got most of it stripped down however the HP fuel lines are in the way....has anybody got an eay way of getting these off?
Also how does the airbox come out from behind the engine?

Thanks for...

Bonjouir from downunder.
Would anyone have the circuit diagram for the control of this flap. It is the slide button type control mounted above the radio. I have the controlling motor removed and it seems to have no faults. The internal gears are ok and on full heat the ac pump turns off ok. I think the problem may be in the dash control unit. I...

hi guys the vacuum pump on my 205 1,8 d has two pipes coming out one obviouslt goes to the breaks and they work fine but the other pipe just sits in the engine bay and is cut off. can someone tell me where this goes to. Thanks

Hi all. I have a 2011 Peugeot 3008 and I am currently having problems with the (front left) ABS system. I have replaced the wheel sensor and also the wheel bearing and the ring sensor, but the ABS and ESP lights are still on. The wheel sensor has been checked and is fine, it seems as though the problem is above the sensor. Could anybody please...

Can anyone tell me if the key on my 2006 307 uses ASK or FSK modulation? Was about to buy one from Aliexpress but my existing key is obviously a universal replacement and does not have either of the original CE0536 / CE0523 markings on it anywhere.

As mentioned elsewhere, I have had issues with our 308CC not charging the battery properly. The alternator does produce current to balance the load, but the output voltage would not rise over 12.8V. usually hovering around 12.5V.

I have tried fitting a second hand alternator from a Mini Cooper with a similar Prince engine, and it is a little...

Hi guys,

I have this problem for a while, that i tried fixing but with no luck, so i came here to ask for your help. :)
Car is Peugeot 508 2011, 2.0 163HP limousine.
Problem that i am encountering is that xenon lights stays in lowest position. When i start the car i get the message (Automatic headlamp height adjustment fault) followed with...

As it just annoyed me.

When it comes to replacing the battery, is there any reason why I can't now use a wet battery of the same size and capacity, instead of the old AGM that is fitted?

Is there any difference in the charging circuit for AGM, that would preclude replacing it with wet?

Cheers

Hi Guys,

2014 Partner Horizon 1.6 Diesel Manual - Wheelchair adapted (for my daughter to use).

New to the forum, I've a good sense of humour and can take a joke and ribbing, I can give as good as I get and I'm not easily offended.

Needing a bit of advice and feedback for a fault code on the ABS ESP system, drove the car on Friday past with...

Afternoon all,

Well she went and did it so I need to expand my knowledge on the new technologies it has.

First off is the electronic parking brake. I've read that these can be a problem so how do they actually work please?

I assume that there is some kind of servo motor which winds the caliper on?

Honestly, I have no idea as I've not even...

Hi, the aircon in my 2004 206 GTi 180 has an intermittent fault. When it first occurred, the fan failed to run, but after a few days it came good. This behaviour kept repeating, but with increasingly longer periods when it wouldn't run, until it eventually it stopped working altogether. I took it to an auto electrician who tested it and said the...

Hi got peugeot boxer 2.0 hdi 2018 model driving along and just cuts out will start and drive again no probs till it cuts out again no warning changed camshaft senor and fuel rail pressure sensor any help would be great

Good evening everyone

I have issue with my hybrid system, the clutch on electric engine is not engaging so I have replaced the whole engine and diff with another working one but it’s still throwing this code P1ABF. I don’t know where else can I look so if someone can help me I would very appreciate that. Thanks...

Hello,

I’ve recently sent my van in for front brakes and discs, cambelt and water pump change and leaky thermostat and then they told me the seals needed to be done on the injectors.( all in £1300) So I got the work done and got the van back (had to set the clock) I then found an oil leak which never existed before!

I asked them to have a look...

Driving back through France to the UK last week the dashboard, and then the centre display, showed these warnings:

IMG_20200902_131145855a.jpg
This showed first and then, when the UREA warning light started flashing, these also came up:

IMG_20200902_162052584a.jpg

IMG_20200902_162103453a.jpg

At one point this message showed. I had...

I have a 2010 60 plate Peugeot 3008 2.0 163 automatic. Fully serviced and looked after.

Yesterday I accelerated hard and the revs went up but as I did so, I heard a loud pop and the car went into limp mode with errors lighting up about the gearbox ,engine, esp, parking brake.

Got home to find a rear blowout and the tyre was completely flat. That...

Hi all, 

I thought I would post this up just in case it helps anyone else in the future with the same issue.  

I have a Vivaro 2021 k0, which is an Expert.  I had an engine fault code pop up and the van went into limp mode.  Scanning gave the following faults:

- P119F Deterioration of the engine oil.  Rate of dilution excessive
- B162C...

Hi, I have topped up my additive tank 30/40k kms ago and reset it on diagbox. Now diagbox tells me there is 95 procent in it but get a pressure fault because it’s empty! How is this possible are the settings not good or is there a internal leak somewhere? There are 2 bolts on top of the tank does anyone know how to remove this?

Do I need to...

Hello
I managed to get the engine out of the van....this engine had less that 30k on it...1.9td. Its in a Ducato motorhome, I can now see the full extent of the damage.
The hole next to the starter motor is where the oil filter housing used to be.
It was lent to someone to help them out and this is how it came back!...there is a hole in each side...

Hello
Does anyone have the torque settings for the main bearing bolts and the big end bolts for the 1.9TD (XUD9)
I have two haynes manuals (405 and Xantia) but the settings are for 1.6...1.8...and 2.0l engines...there doesn't seem to be a mention of 1.9td settings.
Any help appreciated
Thanks.

Hi,

Year 2011, Peugeot 3008 1.6 HDI
VIN VF3**************[VIN obfuscated, can be read by forum staff]

After EGR replacement shows error os disconnection P0405 incorrect position open circuit or short circuit to earth. Had suspicion to it before now look during replacement just got disconnected or it loose cable.

Anybody can point me where to search second end. Loom part number or...

Hi Guys
Am considering the above new vehicle and would love to hear from those who drive one.
Are you happy with the vehicle? Has it been reliable? Would you buy another?

Thanks!

Has the title said,even after the bump a few weeks back the old girl drived ok,
Until today, drove 200miles today to start a new job tomorrow(contractor)
So after finding the site & decent parking decided to get some lunch,that's went the s... hit the fan,pulled over in a layby
A slight bang,little be of smoke or water vapour
Phone a lad who...

Hi!
My name is Daniel and Im writing from Portugal. After reading lots of topics here, I decided to write explaining my problems and making lots of questions hoping someone can help me.

Resume of problems & questions:

1 - The van had two episodes of serious trouble in injection (one injector stucked on open position I think) , making a very loud...

Hi everyone
I’m new to here , but I’m hoping someone can help me who has knowledge or advice. Ok here goes, I’ve just purchased a Peugeot Boxer 1.9td 2001 camper with the XUD 9UTF engine. I’ve just changed the timing belt and finding it difficult to find torque settings. I’ve done as per a manual I’ve purchased the bottom crankshaft bolt to...

Our 2019 308sw 1.5 hdi has started to countdown for its service very early, what can cause this ? The normal service interval should be 12 months or 20000 miles if sooner. It has always been serviced by the Peugeot dealer (Pentagon Lincoln).

It was dealer serviced on 8113 miles on 16/5/2023. Then on about 10002 miles on 21/10/2023 it started to...

Hi - I'm stressed but that is not the word !!!!

I have a 17 plate boxer, its had new water pump and timing belt, thermostat housing as it was losing water and causing a long list of associated problems - they have been solved - head gasket - dpf etc

however now my heat gauge is showing ping over to v hot and the red warning circle light...

Hi everyone! I'm having a very vexing problem with DiagBox 9.150, in short:

I own a Peugeot 208 II

I created an account on the official Peugeot/Citroen website and purchased a token.

For some strange reason I couldn't download DiagBox as there was no link to do so, so I found one online.

I connect to the car using the PC and the OBD cable, the...

I recently bought a 2004 Peugeot 407 2.0 HDi (4-door sedan).

I've noticed that the button to open the boot/trunk does not work.

0 button.jpg

Remote works ok, locks, unlocks and opens the boot. I've already removed the button and checked it with a multimeter, when I press, there is continuity between the two wires on the button, but when I...

Hello everybody!
I already have a strange question for you all :D
I own a Peugeot 206, 1.4 HDi from 2004. Despite all the things you see online, with the ECUs locked by the factory, I managed to successfully activate the cruise control with diagbox, which works perfectly (how delightful it is motorway travelling now :-D ). However, since my car...

Hi

what's the trick to remove the radiator off a 2.7 HDI (so get some free hand / tool space to replace the plastic water flange under the egr )

The cooling fan housing encases the radiator and the air conditioning condensor but I can't see any obvious way to remove the fan housing.

My 508 2.0 hdi had to be jumped started last year and the ecu didn’t like it and stopped working took it to Peugeot and they confirmed it needed another ecu so got a second hand one with the same numbers as the original
It worked fine got the car moted then it stopped working and now comes up say electric circuit fault on the dash and nothing...

Hi New to the forums. I have a Peugeot 2008 with the 1.6 HDI Blue 100 engine. I am having issues with the temperature gauge fluctuating, the car runs up to temperature then rises just below the red section then drops down to just above 90. I have had the car checked out by a auto electrician & he diagnosed the temperature sensor switch was faulty....

Hello guys. I am looking for my first Peugeot car so my wife and me kinda agreed on 3008. We were kinda interested more in 508 but the sitting position is just too low for both of us.

We are looking into used 3008 from a local dealer so I would politely ask somebody to check the VIN number for us. Also if possible please to check what...

I have Peugeot 508 2011 - at some point hade ABS fault, ESP fault, hill asist faults on a dash - disappeared on its own in a day. Appeared again after two three months - I have decided,that it is because of the battery, changed it and it disappeared again. For a week or two... Now ABS, ESP, Hill assist lights on and on top of that I am getting...

My neighbour has handed me the EGR valve from his 15 308 1.6hdi and asked me to 'test it'. Its a Pierburg unit as used on many peugeots and citroens, I think the OEM references would be 1618LN, 1702178, 36001487.
I've looked hard but cant find a technical sheet. Its obviously motor or solenoid operated , connector has 5 (numbered) pins. pin 2 to...

Hello ! how can it be set to measure consumption properly? now it reads one liter less than the actual consumption. peugeot 508 2016
:cry:

After a few weeks after having a new battery fitted i am getting the battery symbol and the stop sign on the dashboard maybe once a week or several time in a five minute journey had the AA back out and they have checked the charging all seems okay garage has check for error code and nothing came up anyone had a anything similar

hello
does anyone have the standard journal sizes for the 1.9td XUD engine?
I have the Haynes manual for the Xantia but it doesnt give the sizes for the 1.9td crankshaft.
I was going to have the crank polished ..or even ground if need be...but it looks to be in excellent nick...remarkably scratch free.
I wanted to measure the journals and...

Hi guys,

I want to change the oil at my EAT6. I went to the servicebox, typed my VIN, and the only thing written regarding oil is JWS 3324 specification.

I asked the dealer for the price, and I was shocked, they told me 130€ for 2 liters.

I went to the other local auto-part stores, and told them about JWS 3324 specification, and the price was...

Hi I have received the following error codes after eml came on
P2125 air mixer
P14a4 egr
P14a3 egr
Vin VF3**************[VIN obfuscated, can be read by forum staff]
The codes have been cleared but what needs to be done so they don't come back.

Thanks 😊

Hello, in my Peugeot 5008 from 2014, I get a red warning light on, when a door is open.
When I drive about 5/10km/h there’s a graphic warning in my navigation screen. There it shows which door is open
Is it possible to get this graphic immediate when the car is not driving and a door is opened?
IMG_6115.jpeg

Hi
I have Peugeot 307 model 2006
The following error appears on the screen:
(Anti pollution faulty)
The car's speed does not exceed 30 km What is the reason, in your opinion, with thanks to the experts?

Recently bought a 205 1.8 turbo diesel, it runs great once ur actually moving however when idling it will slowly rev up and down getting to the point where the dash starts to shake and even stall, im not sure whats causing this as when its cold it idles perfectly. i was wondering if this could be a fuel issue as when i squeese the hand prime the...

Had a strange adventure with my Peugeot 407 2.2 2005 the other day and I don't understand anything. The car has been running fine until this happened. Drove on the highway, suddenly the engine dies and the screen shows that the EPS is not working and depollution system faulty . A friend tows us home. The next day I read about the usual error that...

So how many screws are needed to secure the heater matrix tube?

I see online 1 in the middle, middle and under and all 3

Hello. I am having a nightmare with my 2010 3008.

A light has come on the dash and an error code about the Airbag / Seatbelt tensioner. A fault code of 0362 comes up when a snap on device is plugged into it, suggesting that the Airbag Disable Warning light has malfunctioned (not characterised). The seatbelt display above the centre console shows...