I am frantic to move an 806, outside my Easter host's address in Southampton.
There has been a chattering noise, isolated to a relay situated next to the EMU.
Local resources are unhelpful/unavailable on necessary time scales.
Suggestions include checking fuses and earth connections, and finding specialist advice on the EMU function.
I wonder if anyone has experienced similar problems and can advise? Fuses are located behind the glove box.
The vehicle is petrol 2 litre.
The VIN is VF3**************[VIN obfuscated, can be read by forum staff].
I wonder if anyone can help?
806 fails to start
Moderator: RichardW
-
- Posts: 2
- Joined: 24 Apr 2019, 10:22
- Location: London
- My Cars: Peugeot 806
806 fails to start
Last edited by myglaren on 24 Apr 2019, 11:39, edited 1 time in total.
Reason: VIN masked
Reason: VIN masked
-
OnlineGiveMeABreak
- Forum Admin Team
- Posts: 36993
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5644
Re: 806 fails to start
Ok so this is a 1996 petrol Injection with XU10J2 engine with Magneti Marelli Injection ECU.
Unfortunately you'll need somebody (ideally with Peugeot Planet 2000 diagnostics) to run a diagnostic. That should provide some indications of the issues if there are any faults logged.
Without that it will be guesswork - especially if it has been standing for some time.
According to my info this has a coded ignition - the vehicle won't start without the correct code being entered.
If you've entered the code incorrectly 3 times it will lock down for 30 minutes.
To unblock the coded anti-start keypad, wait at least 30 minutes then switch on the ignition for 1 minute (time to unblock the ECU) before re-entering the code. The injection-ignition ECU will have to be replaced if the user code is lost.
Unfortunately you'll need somebody (ideally with Peugeot Planet 2000 diagnostics) to run a diagnostic. That should provide some indications of the issues if there are any faults logged.
Without that it will be guesswork - especially if it has been standing for some time.
According to my info this has a coded ignition - the vehicle won't start without the correct code being entered.
If you've entered the code incorrectly 3 times it will lock down for 30 minutes.
To unblock the coded anti-start keypad, wait at least 30 minutes then switch on the ignition for 1 minute (time to unblock the ECU) before re-entering the code. The injection-ignition ECU will have to be replaced if the user code is lost.
Please Don't PM Me For Technical Help
Marc
Marc
- white exec
- Moderating Team
- Posts: 7445
- Joined: 21 Dec 2015, 12:46
- Location: Sayalonga, Malaga, Spain
- My Cars: 1996 XM 2.5TD Exclusive hatch RHD
1992 BX19D Millesime hatch LHD
previously 1989 BX19RD, 1998 ZX 1.9D auto, 2001 Xantia 1.8i auto
and lots of Rovers before that: 1935 Ten, 1947 Sixteen, 1960 P5 3-litre, 1966 P6 2000, 1972 P6 2000TC, and 1975 P6B 3500S - x 1752
Re: 806 fails to start
Chattering noise when trying to crank/start suggests battery voltage is low, or a bad starter motor connection.
Try a jump start from another vehicle, and check the main battery connections (battery terminals) after cranking. If either gets at all warm, that indicates a bad connection at/inside the connector.
Try a jump start from another vehicle, and check the main battery connections (battery terminals) after cranking. If either gets at all warm, that indicates a bad connection at/inside the connector.
Chris
-
- New User
- Posts: 1
- Joined: 21 Jun 2020, 09:45
- Location: London
- My Cars: Peugeot 806
Re: 806 fails to start
Hi,
I have the same problem: X 3.
I am seeking capable diagnostic support.
Garage claiming to have pp planet says the vehicle should be off the road.
Can anyone advise reliable source off pp in London/Essex ( I can't seem to access data from the map)?
I have the same problem: X 3.
I am seeking capable diagnostic support.
Garage claiming to have pp planet says the vehicle should be off the road.
Can anyone advise reliable source off pp in London/Essex ( I can't seem to access data from the map)?
Re: 806 fails to start
If you are struggling to get PP2000 if you can get someone with Citroen Lexia that will work fine too on something of this age, just enter it as a Synergie & get an aproximate RP number to enter.
-
OnlineGiveMeABreak
- Forum Admin Team
- Posts: 36993
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5644
Re: 806 fails to start
The map just shows you the locations and the member name, go back to the listing on the Forum thread and click on the member name there in order to see the member's profile and send a private message or email (where they have allowed this). Anyone with Diagbox will be able to diagnose it.Colin Penn wrote: ↑08 Jul 2020, 11:24 Hi,
I have the same problem: X 3.
I am seeking capable diagnostic support.
Garage claiming to have pp planet says the vehicle should be off the road.
Can anyone advise reliable source off pp in London/Essex ( I can't seem to access data from the map)?
Please Don't PM Me For Technical Help
Marc
Marc