Do any of you gentlemen know the torque setting for the deflection pulley on a stretchy belt. The car is a 1.4 hdi 207. I asked the local indie he said gudentite. I rang Peugeot main dealer he helpfully told me to book it in and they would do the pulley. Any help appreciated this is the last job on the car.
Mercy Bucket
Torque setting help needed!
Moderator: RichardW
-
- Posts: 947
- Joined: 16 Oct 2014, 12:17
- Location: Meath Ireland
- My Cars: 2008 Laguna 1.5 DCi
- x 235
Torque setting help needed!
Oh buggle
- GiveMeABreak
- Forum Admin Team
- Posts: 37005
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5646
Re: Torque setting help needed!
I think you mean this little lot:
Reference | Designation | Tightening torques |
(1) | Bolt (Protective cover ) | 0,5 daNm |
(2) | Bolt (Roller tensioner ) | 2,3 daNm |
(3) | Bolt (Camshaft pulley ) | Pre-tighten to 2 daNm Angular tightening to 50° |
(4) | Nut (Roller tensioner ) | 3,7 daNm |
(5) | Stud (Roller tensioner ) | 1 daNm |
(6) | Bolt (Shift prevention bracket) | Tightening to 0,6 m.daN |
Please Don't PM Me For Technical Help
Marc
Marc
-
- Posts: 947
- Joined: 16 Oct 2014, 12:17
- Location: Meath Ireland
- My Cars: 2008 Laguna 1.5 DCi
- x 235
Re: Torque setting help needed!
Hi Marc,
There is just the crank pulley and the alternator pulley on the car, no aircon, and the deflection pulley. It's a stretchy belt. The bolt in no 4 is 37nm? that might be close enough?
Paul
There is just the crank pulley and the alternator pulley on the car, no aircon, and the deflection pulley. It's a stretchy belt. The bolt in no 4 is 37nm? that might be close enough?
Paul
Oh buggle
-
- Posts: 947
- Joined: 16 Oct 2014, 12:17
- Location: Meath Ireland
- My Cars: 2008 Laguna 1.5 DCi
- x 235
Re: Torque setting help needed! Update
I called a different Peugeot dealer he said give me your reg 30 seconds later 5.5 daNm, sorted
Oh buggle
- GiveMeABreak
- Forum Admin Team
- Posts: 37005
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5646
Re: Torque setting help needed!
These are the settings for your engine with and without A/C so I just put them up as they are not separate.
We’re not dealers of course, but try to help people out voluntarily. Peoples’ terminology is different and that is half the battle, but glad you have what you want.
We’re not dealers of course, but try to help people out voluntarily. Peoples’ terminology is different and that is half the battle, but glad you have what you want.
Please Don't PM Me For Technical Help
Marc
Marc
-
- Posts: 947
- Joined: 16 Oct 2014, 12:17
- Location: Meath Ireland
- My Cars: 2008 Laguna 1.5 DCi
- x 235
Re: Torque setting help needed!
Thanks Marc, it's not the timing belt I was replacing only the alternator drive belt. Apparently most of the 1.4's had a spring loaded tensioner some like mine have no tensioner and a stretchy belt. The bearings in the guide pulley are gone on mine at the minute it's just hand tight I didn't want to go down the really tight route in case I strip the hole.
Paul
Paul
Oh buggle