French Car Forum

Hello looking for some advice

I have a 1.6 pertrol THP Citroen C5 mileage is 45K that has been giving me cold start misfires the codes are:- P1336. P1337 (no1 cylinder), P 1339 (no 3 cylinder). I would reset them and the car would run fine apart from slight hesitation during under load. I changed the spark plugs and swapped over the coils but the...

Hello!

I have a Xsara Picasso with a 1.6 HDi, and I have an EGR issue that I can't seem to get rid of.

About a year ago, I replaced the EGR valve, as it was completely shot. Soot even got up into the actuator, so it could barely turn. Evidently, I messed up here because I did not reinitialize it in the ECU. It worked for a while, but I started...

Hi everyone, this is my first post and I'll try not to be too long-winded.
My Peugeot 2008 Allure 1.6 Blue HDI has started displaying several fault lights.
1. Orange - Tyre Pressure Monitoring Fault with beeping noise. Checked pressure and reset the monitor but keeps happening. This is sometimes accompanied with the outside air temp showing...

Hi.
I've been trying for a while to read this C3 1.4i 8v equipped with a Sagem s2pm-380 ECU

The only Sagem ecu offered to me for the C3 are:

-Kfv Sagem s2000pm1 (16v)
-kfv Sagem s2000pm2 (unspecified)

The two first give me a remark:
The computer is not recognized, the validity of the information is not guaranteed

I have access to read...

Hello there,

I am seeking another help to fix fault that is always coming back after deleting ...

U1802 (error in vehicle speed signal - invalid data received)

Everything is working fine like speed on the DashBoard computer and HeadUp Display so I really don't know where to look to fix this fault. Any ideas where to look ?? Thank You in...

Hello ,
I wanted to ask about throttle body, my car is RCZ 2.0hdi and on a car is throttle body with double electronics and double vacuums, but car (motor) has only one vacuum hose and only one electronic cable to connect, so I want to ask is it ok or someone change it somewhen and put with double throttle body? Car always put check on display for...

Hi all

I've got a 2017 Peugeot Boxer, with the 2.0 Euro 6 engine and DCM6.2 engine ECU.
I'm using DiagBox 9.68 running in a virtual machine.
The cable is a 'Lexua full chip' device sourced from AliExpress and I have the S.1279 adaptor that I have set the switch to position 'B' on.
When I start DiagBox I select Boxer 3 (Euro 6). It then scans, but...

As of yesterday I now have a loud wind noise which develops at speeds over about 40 km . It appears to have something to do with cockpit air pressure because as soon as i wind a window down the noise disappears.
It seems to be coming from under the dash board towards the left hand side of the car.

Regards Peter Dowdle

Hi All

Looking for some advice Citroen Relay went into a local garage for a maf sensor fault performance degraded
It was found that two of the leads that run the maf sensor had corroded and had broken off from the plug
The garage sourced a replacement plug cut the wires and jointed a new unit on replaced the maf sensor just in case
A few...

Hi all!

Is there a way to check the genuine total mileage for the 2005 C5 through Lexia? In our country, it's an everyday practice to lower the mileage of any older (or newer, if they are high mileage) car to an eye-watering 200000 km.

I bought mine two years ago with around 220000 km, but I doubt it was that low mileage for a 2005 car. I mean...

The story so far.
I have a 2010 C1, with variable timing. The engine management light is on and its giving me the code P0010, Camshaft sensor /actuator open circuit bank 1.
What I have done so far in the last ten days.
Two engine oil flushes and new oil and filters (no change)
Bench-tested the camshaft position sensor, crankshaft sensor and...

Hi,
I am getting a p0340 error, I have only just replaced both cam and crank sensors and the engine has run for less than 5 min's with the new sensors in, it was not showing any errors when running. It all seemed to be running ok and then it started to falter when i lifted my foot off the throttle then it just stopped and now won't start. I also...

hi, looking to get diagbox as have a clutch switch problem on 2014 c4gp. did you manage to get familiar with it and if so have you got any pointers. thanks

Hi

I've have a 2008 2.0 HDI C5 estate VTR+ just turned into the drive and car cut out and immediately threw an anti pollution message on the display quickly followed by a low oil pressure warning. Checked the oil and it's at the max (checked straight after cut out when oil was warm). I have generic OBD reader but it's burried in the middle of a...

Hey Team

I have a 2014 Citroen DS5, I was wondering what are my options to buy a scan tool
Don't want to pay the outrageous price of $275 NZD each time I want to diognose a problem

What are your favourite scan tools that aren't too expensive

Thanks in advance Marc M

What is this please, dtc U1180, not sure what this does, it's in the oil filter housing.

I’ve recently bought an interface, believed to be genuine by the seller. I was supplied a DVD but it was scratched up and unable to read contents. I’ve tried a few different VM’s of Diagbox but can’t get it to see the interface. Windows 11 picks it up as a PSA interface. Can anyone point me to the tester program I’ve heard a little about please?...

Hi, I'm new to this forum and don't know where to put this information to reach out to all people having the same issu, but ther seems to be alot of people at this fourm having It. I spend the last weeks trying to figure out how to get my computer to recognize my old diag tool (PCA interface: Actia USB com Board Evolution Driver (UMDF) to be...

Hello,
I am really stuck now. I have citroen c4 1.6 hdi 90 with no power at low gears. On 4th and 5th gear is ok. I have check it with snap on and delphi diagnostic and have p0299 and typical egr codes. I was thinking it is the egr first thing but blank it just for test and have the same problem. Yesterday change my turbo as well and no luck at...

After fitting a new turbo & timing kit on a citroen ds5 engine (rhh) the front are not working but the rear wiper does we would welcome any input into
this Regards mickey

Hi, this is my first post. On my way back home my Berlingo suddenly is underpowered and the engine bay is much louder. Although the sound seems like it's coming from the turbo and the turbo shaft has quite a bit of play, and the blades have seen some damage, I don't see a fault code for it. I found a leaking injector and I cleaned it, the same....

I got a Citroen C3 1.6HDI 100 Blue 2015

So a long story short, a while ago I got a problem with communicating with the additive pump (U011887) and some more P error code. So i bought a used replacement additive tank, changed it over, coded it with lexia and diabox, all went well problem solved.

Now half a year later I get the same problem, but...

My first post here after lurking for a while. Apolgies if this is going over old ground...

PSA XS Evolution 9780.Z5 which I aquired with a Peugeot 307cc, but never used. I believe, from my research, that this is a Dealer version of the Lexia. What software should I be using for my 2010 C5, and where do I get it? And how do I use it without...

hi.

I have just installed diagbox.. finally got it working.. v7.58

could somebody please walk me through the steps for coding my ABS ECU into my C3..

I'm completely new to this and worried I may do something disappointingly tragic with such power..

I have no data from the original as it was half full of water at the point of destruction..

I...

I am dealing with a bit problematic C3. It is 1.4 HDi 2005 car after FL and app. 250kkm.
Problem being - engine has no power. It can barely move on leveled ground in 1st gear, no way of getting it uphill.
Revs up to 4000 rpm but has no power.

When cold it will not run without additional gas pedal pressing (keeping it over 1000 rpm). After app....

Hi I have a 2012 3008 1.6 diesel it has had engine replacement but now won't start it cranks ok and fuel is getting to the filter and injectors the only fault I can find is fuel pressure to low on start up is there something I am missing?

2015 Citroën C4 Picasso 1.6 HDi

The engine struggles to start and a couple minutes later a warning message accompanied by a warning sound says there's an issue with the engine and a few seconds later the engine shutdown.

What I already replaced:

Fuel filter
Fuel rail pressure sensor
HP fuel pump regulator valve

I also sent the 4 injectors to...

Year: 2012
Model: Peugeot 3008 1.6 THP Executive
Make: Petrol / Automatic

Hi Everyone,

New Here so Hope I'm Posting this in the Correct Thread, Else Please Let Me Know and I will Move it to The Correct One.

First, I'm No Mechanic, Please Excuse if I Sound like a Total Ass or Ask Stupid Questions.

I Recently got Hold of the Above-Mentioned Car...

Following on from Earlier post regarding the SOS light on my C5 flashing for about the first 5 minutes of motoring.

Reply from Marc suggested I should see fault code FD87 - Which I don't =D>

You need to check if you have this fault code coming up Stu: FD87. If so, it's a replacement of the Independent Telematic Unit. If not, a solid orange...

Hi all new to forum,I have owned my 407 now for 7 years and always been able to sort the many problems.
However this time I can't.
So it starts with the esp light then abs then airbags then tyre pressure then steering then dash goes dead.Engine still running but no gear change.
Once turned off then back on the engine doesn't turn especially...

I haven't been on line for a while, but notice that East Diagnostics appear to have ceased trading. I have had no response on line. I was/am trying to purchase a cd of Peugeot doc backup to use on our Peugeot 2012 207cc. Conversely can anyone help?
Regards, Harry

Having done one of 3 atf fluid changes it's probably time to buy lexia / diagbox as I want to look at spheres and a rear damper too at some point.
I've been looking at the Easydiagnostics website and assume that I need the Lexia3 diagnostic kit as opposed to Citroen Peugeot Lexia, PP2000, Diagbox version 9.68.

Is the latter just an updated...

Does anyone know which fuel gauge law to use for a 2006 Petrol C2?
The background is this ...
I've just fitted a replacement BSI and, after lots of configuring, all seems to be working fine. However, the fuel gauge wasn't displaying and when I checked the BSI the fuel gauge law wasn't present - so I took a punt and set it to Law 01 and the fuel...

Morning all, my wife and I have driven French cars since 30yrs

My Berlingo 108,000kms flashed up P filter add level low yesterday, and I understand it is the eolys fluid resovoir that needs tending to, can anyone state for sure if this is a resevoir back right wheel that takes a top up method, or would it be a pouch to drop into place?

If it is...

Hi all,

I been having a problem with my 206 1.4 HDi where I keep getting one dirty injectors and hence lots of black smoke while accelerating or pushing hard.

So far I have been able to notice some things:

- After injector cleaning, it runs ok for a week on the city, short trips, (one overfuels, another underfuels)
- Starts smelling with...

Hi.
I have just joined the forum after buying a 59 plate C3 Picasso 4 weeks ago, from a garage in Swindon about 90 miles from where i live in South Somerset, it drove OK no problems with the engine, went through all the traffic problems around Bristol and down the M5 and home was pleased the way it drove.
Went out a few days later up the M5 again...

Hi All,
I am looking for a bit of help with an issue I am experiencing with my Vehicle.
The issue is that the car has started to cut-out after the anti-pollution fault flashes on the display on the dash. It doesnt go into limp mode just cuts out. The EML light does not come on.
The car will re-start and can be driven, but can do the same thing at...

Hi thanks for reading, this is my first post on this forum.

My 2012 Peugeot 107 hit a small pot hole on my way home yesterday and I lost power steering immediately accompanied by the P/S warning light on dash, and hasn't worked since. I got out and inspected the car and engine bay for any obvious damage, but have not found anything. Now for as...

Ok best of luck.

I installed the new dpf (the old one was full of soot)
Ever since I did the manual regneration that seemed to not fully complete, I have not been able to communicate with the vehicles ecu!
I was blaming it firstly on the diagbox as this seemed to be giving problems anyway and any functions with it was so slow it was like...

Hi, I want to do manual telecoding in the original diagbox which is activated for one week for my VIN. When I want to do manual telecoding of the BSI, I get the following error: Access to this function not enabled. . I just can read the current configuration / telecoding parameters. I did try other ECUs and there the manual telecoding is working....

help
I bought a second hand loeb 1.6 thp 110 and had problems with it. First I changed cam shafts, filters, chain. It was badly mistreted by owner before me. Flush the engine becouse it was full of sludge.But im still having problems with too rich mixture.After clearing the code its good for 3-4 days and then it start to lose power and has no...

Hello, I have an oil/fuel leak around the injectors, and it's dripping down on the gearbox. So far I have changed the rocker cover gasket, injector seals, and intake manifold. The rocker cover gasket was changed by me so I can be sure that it's done correctly. The intake manifold and injector seals were changed by a mechanic, he said that he...

I'm troubleshooting an issue with my 2017 DS5 VIN: VF7**************[VIN obfuscated, can be read by forum staff] left hand wing mirror.
It's a UK spec Prestige model, so has electronic folding and blind spot monitoring.

Symptoms are that the folding mechanism doesn't work at all (no movement at all, no noises made, no attempt to move) and there is no life for the blind spot LED on that...

Hi,

I installed DiagBox v09.85 on 64 bit Win 10.
When try to use it I get the following message
Access to the vehicle communication card impossible, validate to try again or Cancel to ignore

In order to solve it I disabled the firewall and removed an anti-virus SW and re-started the computer but it didn't help.
My question is if DiagBox can...

Hi everyone. Is there any Members that live in the East Midlands that can Deactivate the TPMS on a 2011 Citroen C5 estate please , willing to pay for the job to be done and travel to you to get the job sorted . Many thanks Mark 👍👍

Hi everyone. Newbie here, I recently posted on another site but got very little response so I’m hoping you guys could possibly help me out.
Recently doing 70mph down Dronfield bypass and the ESP, EGR ABS warning lights came on, along with the SERVICE light and the automatic handbrake light. Did a diagnostic test and got Code P14a3, after some...

Does anyone know if a 2016 308 1.6 blue 120 has an upstream NOx sensor (before the DPF) or if the downstream sensor (after the DPF) is all that it has?

My Autel live data always shows a zero PPM reading for upstream but I get readings for downstream

I'm thinking it doesn't have an upstream sensor, can anyone confirm that?

Hi all,

Anyone has DB cleaner?

I've had VM version 7.57 installed and had to remove it because of storage and the fact I was installing official version for some online telecoding.
Long story short, I have tried installing v7.57 again from same files but it keeps showing as v7.60. It's not letting me do any telecoding.
I do have v7.57 physical...

Hi,

Long story, skip to the end for the question.

I came here sometime in October asking for help surrounding the Diesel Additive Pump on my newly purchased 2012 DS5 Hybrid4. I knew there was an issue with this when purchasing it and was told the fault codes:
B162C 12 (Accessories positive relay control and status inconsistent Relay not...

I'm back on fault finding the cause of thick white unburnt fuel smoke during regen on my 2014 2.2 Boxer campervan.

Something I've noticed on the air intake 2 page of diagbox is the following parameter:

Status of the activation of the correction due to the oxygen sensor - Inactive

This parameter is always inactive during normal driving and...